Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi
080561000
Basic Engraver Set Selected By Author Of Art of Engraving
We asked James B. Meek, author of The Art Of Engraving for his recommendations. This is what he wrote: "Perhaps 90% of all the scroll work in engraving can be done with the following tools". Point Graver No. 4 will cut most scrolls. Fine detail is cut with 0 Point. Knife No. 2 is also for detail. The Square is perhaps the most widely used, can also be sharpened as a point, or a chisel, Flat Nos. 36 and 37, and Round Nos. 50 and 54 are needed for lettering on high relief. Kit contains: Point - Nos. 0 and 4; Square - (2) GlenSteel Blanks; Flat - Nos. 36 and 39; Knife - No. 2; Round - Nos. 50 and 54. 9 gravers total.
SPECS: Approximately 4-3/8" (11.1cm) long. Shank tapers from 3/16" (4.8mm) to 1/16" (1.6mm). Blanks are 4" (10.2cm) long. Steel.
154.9 154.9 1 EUR
Tuotenro: 080561000
BROWNELLS JAMES B. MEEK BEGINNER'S KIT Pyysimme James B. Meek, laatija Art kaiverrus hänen suosituksiaan. Tämä on mitä hän kirjoitti: "ehkä 90 % kaikki Siirry työtä kaiverrus voidaan tehdä seuraavat työkalut". Kohta vakavammat nro 4 leikkaa useimmat rullaa. Yksityiskohtiin on leikattu 0 pistettä. Veitsi nro 2 on myös yksityiskohtaisesti. Aukio on ehkä kaikkein laajalti käytetty, voidaan teroittaa myös, kuten kohta, tai taltta, tasainen nrot 36 ja 37, ja pyöreä nrot 50 ja 54 tarvitaan kirjaimin kohokuva. Kit sisältää: Point - nro 0 ja 4. Square - (2) GlenSteel aihioita; Flat - nro 36 ja 39; Veitsi - nro 2; Kierros - nro 50 ja 54. 9 gravers yhteensä.
154.9 EUR 2 154,90 € *
Toimitusaika noin 2-4 viikkoa.
2 kpl. USA:n varastossa

Ominaisuudet

Toimituksen paino: 0,091kg Korkeus: 58mm Leveys: 61mm Pituus: 173mm

Tuotekuvaus

Made in USA




Basic Engraver Set Selected By Author Of Art of Engraving
We asked James B. Meek, author of The Art Of Engraving for his recommendations. This is what he wrote: "Perhaps 90% of all the scroll work in engraving can be done with the following tools". Point Graver No. 4 will cut most scrolls. Fine detail is cut with 0 Point. Knife No. 2 is also for detail. The Square is perhaps the most widely used, can also be sharpened as a point, or a chisel, Flat Nos. 36 and 37, and Round Nos. 50 and 54 are needed for lettering on high relief. Kit contains: Point - Nos. 0 and 4; Square - (2) GlenSteel Blanks; Flat - Nos. 36 and 39; Knife - No. 2; Round - Nos. 50 and 54. 9 gravers total.
SPECS: Approximately 4-3/8" (11.1cm) long. Shank tapers from 3/16" (4.8mm) to 1/16" (1.6mm). Blanks are 4" (10.2cm) long. Steel.
Uutiskirje