Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi
080561000
Basic Engraver Set Selected By Author Of Art of Engraving
We asked James B. Meek, author of The Art Of Engraving for his recommendations. This is what he wrote: "Perhaps 90% of all the scroll work in engraving can be done with the following tools". Point Graver No. 4 will cut most scrolls. Fine detail is cut with 0 Point. Knife No. 2 is also for detail. The Square is perhaps the most widely used, can also be sharpened as a point, or a chisel, Flat Nos. 36 and 37, and Round Nos. 50 and 54 are needed for lettering on high relief. Kit contains: Point - Nos. 0 and 4; Square - (2) GlenSteel Blanks; Flat - Nos. 36 and 39; Knife - No. 2; Round - Nos. 50 and 54. 9 gravers total.
SPECS: Approximately 4-3/8" (11.1cm) long. Shank tapers from 3/16" (4.8mm) to 1/16" (1.6mm). Blanks are 4" (10.2cm) long. Steel.
184.9 184.9 1 EUR
Tuotenro: 080561000
BROWNELLS JAMES B. MEEK BEGINNER'S KIT Pyydettäessä James B. Meek, kirjan The Art Of Engraving kirjoittaja, suosituksiaan, hän kirjoitti näin: "Ehkä 90% kaikista kaiverruksissa käytettävistä kiehkuroista voidaan tehdä seuraavilla työkaluilla". Point Graver No. 4 leikkaa useimmat kiehkurat. Hienot yksityiskohdat leikataan 0 Pointilla. Knife No. 2 on myös yksityiskohtia varten. Square on ehkä eniten käytetty, sitä voidaan myös teroittaa kärjeksi tai taltaksi, Flat Nos. 36 ja 37 sekä Round Nos. 50 ja 54 ovat tarpeen korkeareliefisessa kirjaimissa. Sarja sisältää: Point - Nos. 0 ja 4; Square - (2) GlenSteel Tyhjät; Flat - Nos. 36 ja 39; Knife - No. 2; Round - Nos. 50 ja 54. Yhteensä 9 kaiverrinta.
184.9 EUR 0 184,90 € *
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.

Ominaisuudet

Toimituksen paino: 0,091kg Toimituksen korkeus: 58mm Toimituksen leveys: 61mm Toimituksen pituus: 173mm

Tuotekuvaus

Made in USA



Basic Engraver Set Selected By Author Of Art of Engraving
We asked James B. Meek, author of The Art Of Engraving for his recommendations. This is what he wrote: "Perhaps 90% of all the scroll work in engraving can be done with the following tools". Point Graver No. 4 will cut most scrolls. Fine detail is cut with 0 Point. Knife No. 2 is also for detail. The Square is perhaps the most widely used, can also be sharpened as a point, or a chisel, Flat Nos. 36 and 37, and Round Nos. 50 and 54 are needed for lettering on high relief. Kit contains: Point - Nos. 0 and 4; Square - (2) GlenSteel Blanks; Flat - Nos. 36 and 39; Knife - No. 2; Round - Nos. 50 and 54. 9 gravers total.
SPECS: Approximately 4-3/8" (11.1cm) long. Shank tapers from 3/16" (4.8mm) to 1/16" (1.6mm). Blanks are 4" (10.2cm) long. Steel.
Uutiskirje