Machined steel firing pin stop is wider and thicker than standard, so you can gunsmith it for a tight fit that helps keep the extractor face square to the case rim for improved extraction and feeding. Bottom edge is left square, ready for final fitting to help slow slide opening and increase dwell-time with major power factor ammunition. Heat-treated to Rc 48, with radiused corners that resist cracking, for a long service life. Available in carbon steel with a tough black oxide finish and stainless steel. Series 70 is sized specifically to give a no-gap fit on .45 ACP Colt Series 70 pistols and clones. Series 80 fits 9mm/.38 Super/.40 S&W/.45 ACP Colt Steries 80 pistols and clones.
Auttaa varmistamaan luotettavan 1911 Auto -hylsynpoiston
Koneistettu teräksinen iskurin pysäytin on leveämpi ja paksumpi kuin vakio, joten voit muokata sitä tiukkaan istuvuuteen, joka auttaa pitämään ulosvetäjän pinnan neliönä hylsyn reunaa vasten parantaen näin hylsynpoistoa ja syöttöä. Alareuna on jätetty suoraksi, valmiina viimeistelyyn, jotta liukumisen avautumista voidaan hidastaa ja lisätä viipymäaikaa suuritehoisella patruunalla. Lämpökäsitelty Rc 48 kovuuteen, ja pyöristetyt kulmat, jotka vastustavat halkeamista, pitkän käyttöiän takaamiseksi. Saatavana hiiliteräksenä, jossa on kestävä musta oksidipinnoite ja ruostumattomana teräksenä. Sarja 70 on erityisesti mitoitettu antamaan saumaton istuvuus .45 ACP Colt Series 70 -pistooleille ja niiden klooneille. Sarja 80 sopii 9mm/.38 Super/.40 S&W/.45 ACP Colt Series 80 -pistooleille ja niiden klooneille.
TEKNISET TIEDOT: Hiiliteräs (CS), musta oksidipinnoite tai ruostumaton teräs (SS), luonnollinen viimeistely. .48” (12mm) leveä, .65” (16.6mm) korkea, .133” (3.3mm) paksu. Vaatii asesepän sovituksen.
Lisää...
Asiakasarviot: EGW O/S FIRING PIN STOP S70 45 SS
Arvioiden lukumäärä: 15
Arvostelut brownells.com sivustolla: 15
Arvioiden keskiarvo: 5
One of the most useful parts you can fit(16.6.2013)
Typical EGW part - superior quality and consistency with lots of value for a few bucks. 1. Eliminate extractor "clocking" 2. Eliminate firing pin stop "self-removal". ;-) 3. File hammer cocking edge at .060", .075" and .100" bevel for 5", 4" and 3" guns to reduce felt recoil and prevent slide from "over-running" the magazine spring... by retarding slide rearward movement. Another EGW part I've used for years and forget to review.
Qaulity firing pin stop by EGW(8.3.2016)
Nice part i would recommend this for someone wanting a tight fitting stop in stainless for an 80series 1911, there are not many options out there this is a good one though. I fit the stop by filing the sides until it could be pushed in by my finger with a snug fit, make sure that you chamfer the bottom of the stop were the hammer rubs.
Excellent quality part(16.10.2009)
These are my favorite FPS to work with. Naturally, being oversized, they will require fitting. I like this as it ensures a perfect fit which reduces the chance of extractor clocking issues. The bottom edge of the FPS is also left square so that it can be custom beveled to your liking. Excellent part.
Stop the Clock.....(24.8.2015)
This product stopped the clocking issue I had on my SA Trophy Match, had to file down the top so this would fit with my sight configuration. File and stone to fit and all issues were solved. Very well made with great service from Brownells
Awesome Quality - TUNING REQUIRED!(4.2.2010)
Excellent reproduction of Browning's pre-1917 short-radius firing pin stop. Delays unlocking of action, less recoil, less muzzle flip and cleaner breech area. Designed by Browning to be used in a 5" Government Model with a 14.0lb Recoil Spring and 23.0lb Mainspring. This is CRITICAL. When fitting, simply break the edge with a stone, about .030" wide. The hammer will do the rest.
Only one to use(19.3.2010)
OS so you can tune it to an interferance fit. Old FPS would just fall out. Lots of slop.Very easy to work with.
Wouldn't use another(17.8.2010)
This is not a drop in part. It must be fitted. The benefits pay off it fitted properly. 10851Man said it right.
High Quality!(11.11.2010)
This (in conjunction with an Ed Brown extractor) fixed my extract/eject issues in my Springfield. It is an oversized FPS so fitting is required but is the only way to achieve the fit I desired. I highly recommend this piece. It is great quality.
DROPPED RIGHT IN(16.2.2012)
with a little filing to smooth it dropped right in and just needed the bottom rounded.
For a tight fit(7.11.2015)
Like all of EGW parts I have used this one is solid. Plenty of material on the pin stop to ensure a nice tight fitted part.
Thank You EGW(6.8.2016)
Finally, or I just may be late to the game, a firing pin stop that cures clocking. I have now installed this firing pin stop in four different brands of 1911s and have been very pleased with the results. Fitting times may vary, but the average is about 30 minutes, start to finish. This is not a drop-in part. Elbow grease is required. Also, for best results, just lightly burnish the leading edge instead of rounding it off like the factories do. If you want a radiused FPS, buy a drop-in. But, if you want a tight fit that also slows down the recoil impulse, get one of these.
Very nicely made(25.10.2009)
I had to do a little fitting as expected. Also, I put a very small chamfer on the outward edge that would contact the hammer.
I used this on a full sized 1911 with a 16 lb recoil spring and it is an awsome combination. Reduces the jumpiness of the pistol to better control recoil.
I will be adding one of these to my 4 inch Kimber.
great(8.9.2011)
fitted this to my Colt GCNM S80 & it helped taming the muzzle flip as well as making sure the extractor doesn't clock, with no radius it was quite hard to pull the slide with the hammer down but i can live with that as it was the way JMB designed it to be.
Took Some Work To Fit(7.12.2011)
Will take some work to fit. Put on my Colt Commander. Cut a small radius on the bottom. Shot a 100 rds, then added a little more radius, then shot another 100 rds. This FPS, with a slightly radius bottom, definitely controls the muzzle flip, significantly! Now that I practiced with the 15 dollar part, I will order the SS FPS, since my Colt is SS.
Take your time fitting and you will be happy with the results.
Easy Fit(5.1.2015)
Ordered two of these for 80 Series Colts, required very little "fitting" 440 and 1000 grit paper and a piece of glass to keep it all straight. Less than 10 minutes total time to fit and install both.
Tuotenro: 296000131 EGW O/S FIRING PIN STOP S70 45 SS Valmistajan tuotenumero: 10361841370100835 Koneistettu teräksinen iskurin pysäytin on leveämpi ja paksumpi kuin vakio, joten voit muokata sitä tiukkaan istuvuuteen, joka auttaa pitämään ulosvetäjän pinnan neliönä hylsyn reunaa vasten parantaen näin hylsynpoistoa ja syöttöä. Alareuna on jätetty suoraksi, valmiina viimeistelyyn, jotta liukumisen avautumista voidaan hidastaa ja lisätä viipymäaikaa suuritehoisella patruunalla. Lämpökäsitelty Rc 48 kovuuteen, ja pyöristetyt kulmat, jotka vastustavat halkeamista, pitkän käyttöiän takaamiseksi. Saatavana hiiliteräksenä, jossa on kestävä musta oksidipinnoite ja ruostumattomana teräksenä. Sarja 70 on erityisesti mitoitettu antamaan saumaton istuvuus .45 ACP Colt Series 70 -pistooleille ja niiden klooneille. Sarja 80 sopii 9mm/.38 Super/.40 S&W/.45 ACP Colt Series 80 -pistooleille ja niiden klooneille.
39.9EUR839,90 €
*
Toimitusaika noin 2-4 viikkoa. 8 kpl. USA:n varastossa
Made in USA
USA:n vientiluvan tyyppi: 0A501.x
USA:n hallitus kontrolloi näitä tuotteita. Niiden vienti USA:sta on sallittu vain siihen maahan, johon ne on tilattu, ja vain vastaanottajan tai loppukäyttäjän käyttöön. Niitä ei saa uudelleenmyydä, siirtää tai luovuttaa mihinkään muuhun maahan tai muulle henkilölle kuin vastaanottajalle tai loppukäyttäjälle, ei alkuperäisessä muodossaan eikä muiden tuotteiden osana, ilman etukäteen hankittua lupaa USA:n hallitukselta tai muuta USA:n lakiin ja määräyksiin perustuvaa hyväksyntää.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Tuotenro: 296100001 EGW O/S FIRING PIN STOP S80 38/9/40 BLUE Valmistajan tuotenumero: 10362841370100842 Koneistettu teräksinen iskurin pysäytin on leveämpi ja paksumpi kuin vakio, joten voit muokata sitä tiukkaan istuvuuteen, joka auttaa pitämään ulosvetäjän pinnan neliönä hylsyn reunaa vasten parantaen näin hylsynpoistoa ja syöttöä. Alareuna on jätetty suoraksi, valmiina viimeistelyyn, jotta liukumisen avautumista voidaan hidastaa ja lisätä viipymäaikaa suuritehoisella patruunalla. Lämpökäsitelty Rc 48 kovuuteen, ja pyöristetyt kulmat, jotka vastustavat halkeamista, pitkän käyttöiän takaamiseksi. Saatavana hiiliteräksenä, jossa on kestävä musta oksidipinnoite ja ruostumattomana teräksenä. Sarja 70 on erityisesti mitoitettu antamaan saumaton istuvuus .45 ACP Colt Series 70 -pistooleille ja niiden klooneille. Sarja 80 sopii 9mm/.38 Super/.40 S&W/.45 ACP Colt Series 80 -pistooleille ja niiden klooneille.
29.9EUR729,90 €
*
Toimitusaika noin 2-4 viikkoa. 7 kpl. USA:n varastossa
Tuotenro: 296000132 EGW O/S FIRING PIN STOP S80 38/9/40 SS Valmistajan tuotenumero: 10363841370100859 Koneistettu teräksinen iskurin pysäytin on leveämpi ja paksumpi kuin vakio, joten voit muokata sitä tiukkaan istuvuuteen, joka auttaa pitämään ulosvetäjän pinnan neliönä hylsyn reunaa vasten parantaen näin hylsynpoistoa ja syöttöä. Alareuna on jätetty suoraksi, valmiina viimeistelyyn, jotta liukumisen avautumista voidaan hidastaa ja lisätä viipymäaikaa suuritehoisella patruunalla. Lämpökäsitelty Rc 48 kovuuteen, ja pyöristetyt kulmat, jotka vastustavat halkeamista, pitkän käyttöiän takaamiseksi. Saatavana hiiliteräksenä, jossa on kestävä musta oksidipinnoite ja ruostumattomana teräksenä. Sarja 70 on erityisesti mitoitettu antamaan saumaton istuvuus .45 ACP Colt Series 70 -pistooleille ja niiden klooneille. Sarja 80 sopii 9mm/.38 Super/.40 S&W/.45 ACP Colt Series 80 -pistooleille ja niiden klooneille.
39.9EUR439,90 €
*
Toimitusaika noin 2-4 viikkoa. 4 kpl. USA:n varastossa
Tuotenro: 296000058 EGW O/S FIRING PIN STOP S70 45 BLUE Valmistajan tuotenumero: 10360841370100828 Koneistettu teräksinen iskurin pysäytin on leveämpi ja paksumpi kuin vakio, joten voit muokata sitä tiukkaan istuvuuteen, joka auttaa pitämään ulosvetäjän pinnan neliönä hylsyn reunaa vasten parantaen näin hylsynpoistoa ja syöttöä. Alareuna on jätetty suoraksi, valmiina viimeistelyyn, jotta liukumisen avautumista voidaan hidastaa ja lisätä viipymäaikaa suuritehoisella patruunalla. Lämpökäsitelty Rc 48 kovuuteen, ja pyöristetyt kulmat, jotka vastustavat halkeamista, pitkän käyttöiän takaamiseksi. Saatavana hiiliteräksenä, jossa on kestävä musta oksidipinnoite ja ruostumattomana teräksenä. Sarja 70 on erityisesti mitoitettu antamaan saumaton istuvuus .45 ACP Colt Series 70 -pistooleille ja niiden klooneille. Sarja 80 sopii 9mm/.38 Super/.40 S&W/.45 ACP Colt Series 80 -pistooleille ja niiden klooneille.
33.9EUR033,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Machined steel firing pin stop is wider and thicker than standard, so you can gunsmith it for a tight fit that helps keep the extractor face square to the case rim for improved extraction and feeding. Bottom edge is left square, ready for final fitting to help slow slide opening and increase dwell-time with major power factor ammunition. Heat-treated to Rc 48, with radiused corners that resist cracking, for a long service life. Available in carbon steel with a tough black oxide finish and stainless steel. Series 70 is sized specifically to give a no-gap fit on .45 ACP Colt Series 70 pistols and clones. Series 80 fits 9mm/.38 Super/.40 S&W/.45 ACP Colt Steries 80 pistols and clones.
Auttaa varmistamaan luotettavan 1911 Auto -hylsynpoiston
Koneistettu teräksinen iskurin pysäytin on leveämpi ja paksumpi kuin vakio, joten voit muokata sitä tiukkaan istuvuuteen, joka auttaa pitämään ulosvetäjän pinnan neliönä hylsyn reunaa vasten parantaen näin hylsynpoistoa ja syöttöä. Alareuna on jätetty suoraksi, valmiina viimeistelyyn, jotta liukumisen avautumista voidaan hidastaa ja lisätä viipymäaikaa suuritehoisella patruunalla. Lämpökäsitelty Rc 48 kovuuteen, ja pyöristetyt kulmat, jotka vastustavat halkeamista, pitkän käyttöiän takaamiseksi. Saatavana hiiliteräksenä, jossa on kestävä musta oksidipinnoite ja ruostumattomana teräksenä. Sarja 70 on erityisesti mitoitettu antamaan saumaton istuvuus .45 ACP Colt Series 70 -pistooleille ja niiden klooneille. Sarja 80 sopii 9mm/.38 Super/.40 S&W/.45 ACP Colt Series 80 -pistooleille ja niiden klooneille.
TEKNISET TIEDOT: Hiiliteräs (CS), musta oksidipinnoite tai ruostumaton teräs (SS), luonnollinen viimeistely. .48” (12mm) leveä, .65” (16.6mm) korkea, .133” (3.3mm) paksu. Vaatii asesepän sovituksen.
Lisää...
Asiakasarviot: EGW O/S FIRING PIN STOP S70 45 SS
Arvioiden lukumäärä: 15
Arvostelut brownells.com sivustolla: 15
Arvioiden keskiarvo: 5
One of the most useful parts you can fit(16.6.2013)
Typical EGW part - superior quality and consistency with lots of value for a few bucks. 1. Eliminate extractor "clocking" 2. Eliminate firing pin stop "self-removal". ;-) 3. File hammer cocking edge at .060", .075" and .100" bevel for 5", 4" and 3" guns to reduce felt recoil and prevent slide from "over-running" the magazine spring... by retarding slide rearward movement. Another EGW part I've used for years and forget to review.
Qaulity firing pin stop by EGW(8.3.2016)
Nice part i would recommend this for someone wanting a tight fitting stop in stainless for an 80series 1911, there are not many options out there this is a good one though. I fit the stop by filing the sides until it could be pushed in by my finger with a snug fit, make sure that you chamfer the bottom of the stop were the hammer rubs.
Excellent quality part(16.10.2009)
These are my favorite FPS to work with. Naturally, being oversized, they will require fitting. I like this as it ensures a perfect fit which reduces the chance of extractor clocking issues. The bottom edge of the FPS is also left square so that it can be custom beveled to your liking. Excellent part.
Stop the Clock.....(24.8.2015)
This product stopped the clocking issue I had on my SA Trophy Match, had to file down the top so this would fit with my sight configuration. File and stone to fit and all issues were solved. Very well made with great service from Brownells
Awesome Quality - TUNING REQUIRED!(4.2.2010)
Excellent reproduction of Browning's pre-1917 short-radius firing pin stop. Delays unlocking of action, less recoil, less muzzle flip and cleaner breech area. Designed by Browning to be used in a 5" Government Model with a 14.0lb Recoil Spring and 23.0lb Mainspring. This is CRITICAL. When fitting, simply break the edge with a stone, about .030" wide. The hammer will do the rest.
Only one to use(19.3.2010)
OS so you can tune it to an interferance fit. Old FPS would just fall out. Lots of slop.Very easy to work with.
Wouldn't use another(17.8.2010)
This is not a drop in part. It must be fitted. The benefits pay off it fitted properly. 10851Man said it right.
High Quality!(11.11.2010)
This (in conjunction with an Ed Brown extractor) fixed my extract/eject issues in my Springfield. It is an oversized FPS so fitting is required but is the only way to achieve the fit I desired. I highly recommend this piece. It is great quality.
DROPPED RIGHT IN(16.2.2012)
with a little filing to smooth it dropped right in and just needed the bottom rounded.
For a tight fit(7.11.2015)
Like all of EGW parts I have used this one is solid. Plenty of material on the pin stop to ensure a nice tight fitted part.
Thank You EGW(6.8.2016)
Finally, or I just may be late to the game, a firing pin stop that cures clocking. I have now installed this firing pin stop in four different brands of 1911s and have been very pleased with the results. Fitting times may vary, but the average is about 30 minutes, start to finish. This is not a drop-in part. Elbow grease is required. Also, for best results, just lightly burnish the leading edge instead of rounding it off like the factories do. If you want a radiused FPS, buy a drop-in. But, if you want a tight fit that also slows down the recoil impulse, get one of these.
Very nicely made(25.10.2009)
I had to do a little fitting as expected. Also, I put a very small chamfer on the outward edge that would contact the hammer.
I used this on a full sized 1911 with a 16 lb recoil spring and it is an awsome combination. Reduces the jumpiness of the pistol to better control recoil.
I will be adding one of these to my 4 inch Kimber.
great(8.9.2011)
fitted this to my Colt GCNM S80 & it helped taming the muzzle flip as well as making sure the extractor doesn't clock, with no radius it was quite hard to pull the slide with the hammer down but i can live with that as it was the way JMB designed it to be.
Took Some Work To Fit(7.12.2011)
Will take some work to fit. Put on my Colt Commander. Cut a small radius on the bottom. Shot a 100 rds, then added a little more radius, then shot another 100 rds. This FPS, with a slightly radius bottom, definitely controls the muzzle flip, significantly! Now that I practiced with the 15 dollar part, I will order the SS FPS, since my Colt is SS.
Take your time fitting and you will be happy with the results.
Easy Fit(5.1.2015)
Ordered two of these for 80 Series Colts, required very little "fitting" 440 and 1000 grit paper and a piece of glass to keep it all straight. Less than 10 minutes total time to fit and install both.