Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Laadukas S&W M&P TRIJICON RMR SIGHT MOUNT EGW:ltä
EGW:n valmistama S&W M&P TRIJICON RMR SIGHT MOUNT on suunniteltu erityisesti Smith & Wesson M&P -sarjan aseille, tarjoten luotettavan ja kestävän tavan kiinnittää Trijicon RMR punapiste-kiikari. Tämä mount on valmistettu korkealaatuisesta 7075-alumiinista ja siinä on matta musta hardcoat -pinnoite.
Tuotteen tiedot:
- Materiaali: 7075 Alumiini
- Pinnoite: Matta Musta Hardcoat
- Kokonaispituus: 1.780"
- Kokonaisleveys: 1.1"
- Kiinnitystarvikkeet: (2) 6-32 Flat Head ruuvia, (1) 6-32 X 3/16 Set Screw
- Punapisteen yhteensopivuus: Trijicon RMR
Yhteensopivuus:
Mount sopii seuraaviin:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Mount ei sovi seuraaviin:
- Smith & Wesson M&P Shield (Mount on liian leveä Shieldille)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Ei sovi M&P .22 Compact -malliin. Smith and Wessonin takatähtien mitat voivat vaihdella. Meidän tähtimme on valmistettu samoilla toleransseilla. Joillakin käyttäjillä saattaa olla ongelmia asennettaessa levyämme liukusäätimelle vaihtelevien toleranssien vuoksi. Huomioithan tämän tilatessasi.
Asennus tulee suorittaa ja tarkistaa pätevän asekorjaajan toimesta. Tuotteen virheellisestä asennuksesta tai käytöstä aiheutuvista vahingoista tai vammoista ei ole vastuuta.
Asennusohjeet:
- Poista takatähtäin*
- Asenna EGW Sight Mount dovetailen
- Kiristä set screw (jos sovellettavissa)
- Aseta punapiste-kiikari EGW Sight Mountille (pienet paperipalat punapisteen ja sight mountin väliin helpottavat irrottamista ja pitävät Loctitea pois punapiste-kiikarista)
- Levitä sinistä Loctitea mukana tuleville kiinnitysriveille
- Kiristä kiinnitysrivejä 15in/lbs
*Takatähtäimen työntötyökalua suositellaan vahvasti.