Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
S&W K, L, N, X FRAME REVOLVERS VORTEX RAZOR SIGHT MOUNT

841370113019 296000691
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.  
84.9 84.9 1 EUR
Tuotenro: 296000691
EGW SIGHT MOUNT FOR VORTEX RAZOR FITS S&W K, L, N, X FRAME BLACK
Valmistajan tuotenumero: 49438 841370113019 Poista vain aseen takatähtäin ja korvaa se EGW:n kiinnityksellä, jotta voit asentaa Vortex Razor-, C-More RTS- tai STS-punapistetähtäimen. Voit milloin tahansa irrottaa kiinnityksen ja palauttaa takatähtäimen paikoilleen. Kiinnitystarvikkeet sisältyvät pakettiin. Asennusohjeet: Poista takatähtäin* Asenna EGW Tähtäinkisko uraan Kiristä asetuspultti (jos sovellettavissa) Aseta punapistetähtäin EGW Tähtäinkiskoon (punapistetähtäimen ja tähtäinkiskon väliin asetettu pieni paperipala helpottaa irrottamista ja pitää Loctiten poissa punapistetähtäimestä.) Levitä sinistä Loctitea mukana tuleviin kiinnitysruuveihin Kiristä kiinnitysruuvit momenttiin 15in/lbs Mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Tämä kiinnitys sopii: Smith & Wesson K Frame -revolverit Smith & Wesson L Frame -revolverit Smith & Wesson N Frame -revolverit Smith & Wesson X Frame -revolverit Jos revolverissasi ei ole esiporattuja ja kierteitettyjä reikiä, tämä kiinnitys ei sovellu käytettäväksi. Paras tapa varmistaa, onko ase porattu ja kierteitetty, on avata rullan ja tarkistaa alla oleva kisko. Siinä tulisi olla läpimenoreiät, jotka ovat poratut ja kierteitetyt. Jos niitä ei ole (kuten yllä olevassa kuvassa), tämä kiinnitys ei sovellu käytettäväksi ilman, että ase porataan ja kierteitetään. Voit antaa pätevän ja kelpoisen aseasepän porata ja kierteittää ylähihnan standardin S&W-reikäkuvion mukaisesti, mikä mahdollistaa meidän kiinnityksemme käytön.
84.9 EUR 1 84,90 € *
Toimitusaika noin 2-4 viikkoa.
1 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: K Frame, L Frame, N Frame, X Frame Materiaali: Aluminum Merkki: Smith & Wesson Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: N Frame,K Frame,X Frame,L Frame Materiaali: Aluminum Tyyli: Tactical Valmistaja: Smith & Wesson Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.  
Uutiskirje