Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter. FITS: Sig P210 Target (American Only Post 2016) EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Esittely: SIG SAUER P210A TARGET VORTEX VIPER/VENOM SIGHT MOUNT
EGW:n valmistama SIG SAUER P210A TARGET VORTEX VIPER/VENOM SIGHT MOUNT on täydellinen lisävaruste, joka mahdollistaa tarkkuusammunnan ja nopean kohdistamisen.
Tuotteen tiedot:
- Materiaali: 7075 Alumiini
- Päällyste: Matte Black Hardcoat
- Kokonaispituus: 1.811"
- Kokonaisleveys: .99"
- Asennuskiinnikkeet: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
- Red Dot -sovitus: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
- Yhteensopivuus: Sig P210 Target (amerikkalainen malli vain vuoden 2016 jälkeen)
EGW:n punapisteet on tarkoitettu asennettavaksi vasemmalta oikealle (piippu eteenpäin). Dovetail-muotoilu helpottaa asennusta. Poista aseen takasight ja vaihda se EGW:n kiinnitykseen, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter punapisteen. Muutoksia ei vaadita, ja voit aina poistaa kiinnityksen ja vaihtaa takasightin takaisin.
Asennusohjeet:
- Poista takasight
- Asenna EGW Sight Mount dovetailiin
- Tiukkaa set screw (jos sovellettavissa)
- Aseta punapistesight EGW Sight Mountiin (pieni paperinpala punapistesightin ja kiinnityksen väliin helpottaa poistamista ja pitää Loctite:n poissa punapistesightista)
- Käytä sinistä Loctite:a mukana toimitettuihin asennusruuveihin
- Täytä asennusruuvit 15in/lbs vääntömomentilla
Ruuvit:
- 2 Button Head Cap Screws - Vortex Viper ja Venom Sightseille
- 2 Flat Head Cap Screws - Burris FastFire ja Docter Sightseille
Asennukseen tarvitaan 5/64'' allen-avain.