Hundreds of abrasive "balls" mounted on a flexible shaft - the fastest, easiest way we've come across to clean and polish older barrels or put a mirror polish in new ones. For used barrels, the Medium-Coarse hone, followed by the Fine, removes rough and tight spots and brings the bore to a bright finish that you can see and feel . . . just run a patch through it before and after; the difference is amazing! We found too, that we could feel tight spots during honing and spend extra time on them until they were evened out. On new barrels, the Fine hone by itself will bring the factory finish up to a beautiful, mirror-bright finish that's a real customer pleaser. Easy to use: chuck in a variable speed electric drill; wet the hone with Flex Hone® oil; start the drill and insert the hone into the barrel from the breech end (if possible). As it cuts, a slurry of abrasive and oil develops to help speed the cutting action. Flex Hone® available (shown below) in sets and individual hones for 10, 12, 16 and 20 gauge barrels as well as .410 bore. Also, special-sized hones for 10, 12, 16, 20 gauge chambers and .410 bore. Instructions walk you through the steps for a perfect job. (You MUST use Flex Hone® oil - all other oils will destroy the abrasive "balls" and void our guarantee!) 750 RPM MAX. Avoid excess pressure. View Flex-Hone PDF Here
SPECS: Flex Hone for Barrels; 10, 12, 16, 20 ga., .410 bore. 33" (83.8cm) long in Med.-Coarse grit (red tip) or Fine grit (light blue tip). Flex Hone for Chambers; 10, 12, 16, 20 ga., .410 bore 12" (6.5cm) long, fine grit (light blue only). Set includes Med.-Coarse & Fine barrel hones, Chamber hone & 1 qt. Flex Hone oil, for 1 ga.
Medium grit is 180 grit silicon carbide and Fine grit is 800 grit aluminum oxide.
Erinomainen viimeistely haulikkotunneleille
SHOTGUN BARREL POLISHING FLEX HONE®, 12 GAUGE FINE FLEX HONE, BORE on paras tapa puhdistaa ja kiillottaa vanhoja piippuja tai saada uudet piiput peilimäiseen kuntoon. Tämä innovatiivinen työkalu sisältää satoja hiontapalloja joustavalla varrella, mikä tekee siitä nopean ja helpon ratkaisun.
Tuotteen ominaisuudet:
- Tehokas puhdistus: Keskikarkea hionta ja hieno hionta poistavat karkean pinnan ja tiukat kohdat, tuoden piipun kirkkaaksi.
- Helppokäyttöinen: Kiinnitä muunneltavan nopeuden sähköporakoneeseen; kostuta hionta Flex Hone® -öljyllä ja vie se piippuun.
- Erinomainen lopputulos: Uusille piipuille hieno hionta tuo tehtaan viimeistelyn kauniiseen, peilimäiseen kuntoon.
Huomioi: Käytä aina Flex Hone® -öljyä, muut öljyt tuhoavat hiontapalloja ja mitätöivät takuun. Vältä liiallista painetta. Maksimi nopeus 750 RPM.
Tekniset tiedot:
- Flex Hone piipuissa; 10, 12, 16, 20 ga., .410 bore.
- Pituus: 33" (83.8cm) keskikarkea hionta (punainen kärki) tai hieno hionta (vaaleansininen kärki).
- Flex Hone kammiin; 10, 12, 16, 20 ga., .410 bore, 12" (6.5cm) pitkä, vain hieno hionta (vaaleansininen).
- Setti sisältää keskikarkean ja hienon piippuhionnan, kammi-hionnan ja 1 qt. Flex Hone -öljyä.
- Keskikarkea hionta on 180 grit silikonikarbidia ja hieno hionta on 800 grit alumiinioksidia.
Katso Flex-Hone PDF täältä.