Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
SAVAGE RASCAL CUT FOR WILLIAMS SIGHT PICATINNY SCOPE MOUNT

841370113675 296000612
This mount was designed for use with the Williams FP-GR TK peep sight. The corresponding front sight and block from Williams are: Lyman Globe Front Sight Williams Rear Sight Top of the receiver to the top of the rear sight dovetail is .330" Top of the receiver to the top of the picatinny rail is .45" This rail is ambidextrous. This mount is milled on both sides for bolt clearance on left or right handed models. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW's one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. They machine these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type II anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is  sold separately). The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.
69.9 69.9 1 EUR
Tuotenro: 296000612
EGW SAVAGE RASCAL CUT FOR WILLIAMS SIGHT PICATINNY BASE 0 MOA
Valmistajan tuotenumero: 41965 841370113675 Tämä kiinnike on suunniteltu käytettäväksi Williams FP-GR TK -tähtäimen kanssa. Vastaavat etutähtäin ja lohko Williamsilta ovat: Lyman Globe Front Sight Williams Rear Sight Tukin yläosasta takatähtäimen uran yläosaan on .330" Tukin yläosasta Picatinny-kiskon yläosaan on .45" Tämä kisko on ambidekstraalinen. Kiinnike on jyrsitty molemmilta puolilta varmistamaan pulttien väistötila vasen- tai oikeakätisissä malleissa. Picatinny-urat kulkevat koko kiskon pituuden, mikä antaa ampujalle joustavuutta kiikarinrenkaiden ja muiden varusteiden kiinnityksessä. Kiskon keskellä oleva kanava vähentää kiinnikkeen kokonaismassaa. Lisäksi monissa tapauksissa se ei estä tehdasvalmisteisten rautatähtäimien käyttöä. EGW:n yksiosaiset kiikaritähtäinkiskot ovat ilmeinen valinta niin metsästäjille kuin taktisille ampujillekin. He valmistavat nämä kiskot omassa työpajassaan käyttäen yhtä heidän koneistuskeskuksistaan. Koneistuksen jälkeen kiinnikkeet tasoitetaan, hiekkapuhalletaan ja anodisoidaan Type II -menetelmällä pitkäkestoisen kestävyyden takaamiseksi. Asennus: EGW suosittelee 20 tuumaa paunaa vääntömomenttia ja tipan sinistä loctitea (loctite myydään erikseen). Koko kiinnike ja tarvikkeet (asennusruuveista ja avaimesta pakkaukseen) on valmistettu Yhdysvalloissa.
69.9 EUR 3 69,90 € *
Toimitusaika noin 2-4 viikkoa.
3 kpl. USA:n varastossa
Ominaisuudet: Elevation: 0 MOA Jalustojen lukumäärä: 1-Piece Malli: Rascal Materiaali: Aluminum Merkki: Savage Arms Tyyppi: Picatinny Rail Väri: Black

Ominaisuudet

Elevation: 0 MOA Jalustojen lukumäärä: 1-Piece Malli: Rascal Materiaali: Aluminum Tyyli: Picatinny Rail Valmistaja: Savage Arms Väri: Black Toimituksen paino: 0,091kg Toimituksen korkeus: 25mm Toimituksen leveys: 102mm Toimituksen pituus: 229mm

Tuotekuvaus

Made in USA



This mount was designed for use with the Williams FP-GR TK peep sight. The corresponding front sight and block from Williams are: Lyman Globe Front Sight Williams Rear Sight Top of the receiver to the top of the rear sight dovetail is .330" Top of the receiver to the top of the picatinny rail is .45" This rail is ambidextrous. This mount is milled on both sides for bolt clearance on left or right handed models. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW's one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. They machine these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type II anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is  sold separately). The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.
Uutiskirje