Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
RUGER® MK I, II, III, IV, P85, P90 TRIJICON RMR SIGHT MOUNT

841370116522 296000580
Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780" Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR, Holosun HS507C Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation.
84.9 84.9 1 EUR
Tuotenro: 296000580
EGW RUGER® MKI, II, III, IV, P85, P90 TRIJICON RMR SIGHT MOUNT
Valmistajan tuotenumero: 49521 841370116522 Materiaali: 7075 Alumiini Päällyste: Mattamusta kovapinnoite Kokonaispituus: 1,780" Kokonaisleveys: 1,1" Kiinnitystarvikkeet: (2) 6-32 Litteä pääruuvit, (1) 6-32 X 3/16 Asetusruuvi Punapistetähtäimen yhteensopivuus: Trijicon RMR, Holosun HS507C Poista vain aseen takatähtäin ja korvaa se meidän kiinnikkeellämme, jotta voit asentaa Trijicon RMR -punapistetähtäimen. Muutoksia ei vaadita. Voit milloin tahansa ottaa kiinnikkeemme pois ja vaihtaa takatähtäimen takaisin. Kiinnitystarvikkeet sisältyvät. Asennusohjeet Poista takatähtäin* Asenna EGW-tähtäinkiinnike irtosovitteeseen Kiristä asetusruuvi (jos sovellettavissa) Aseta punapistetähtäin EGW-tähtäinkiinnikkeelle (punapistetähtäimen ja kiinnikkeen väliin asetettu pieni paperinpala helpottaa poistamista ja pitää Loctiten pois punapistetähtäimestä.) Levitä sinistä Loctite-liimaa mukana tulleisiin kiinnitysruuveihin Kiristä kiinnitysruuvit 15in/lbs momenttiin 2 Litteä pääkannen ruuvit - Mukana Trijicon RMR:lle Mukana tulevat ruuvit vaativat 5/64'' kuusiokoloavaimen asennukseen.
84.9 EUR 0 84,90 € *
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: Mark III, Mark I, Mark II, P89, 22/45, Mark IV, P85, P97 Materiaali: Aluminum Merkki: Ruger Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: 22/45,Mark I,Mark II,Mark III,Mark IV,P85,P89,P97 Materiaali: Aluminum Tyyli: Tactical Valmistaja: Ruger Väri: Black Toimituksen paino: 0,032kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 133mm

Tuotekuvaus

Made in USA



Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780" Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR, Holosun HS507C Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation.
Uutiskirje