Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi
100045341
Ted Yost developed and made these sights several years ago and after a long absence from the marketplace they are once again available from Harrison Design. These sights can be used to rescue a slide from mis-cut front dovetails. They have an oversize dovetail base featuring nominal dimensions of .085"" depth, .375"" width with a 65 dovetail angle. That's big enough to rescue most any sort of ugliness and butchery. The blade is .275"" tall X .630"" long X .125 wide. The vertical rill pin has been omitted so you can match it's location to wherever your slide's hole location is located. The dovetail base is .625"" wide, so it can be blended to the top of your slide, or youcan cut the sides back for the appearance you want. A radius is machined at the point where the blade joins the dovetail base, strengthening the sight appreciably. This is a part that every gunsmith should keep 2 or 3 of on hand as it can get you out of a jam is a slip up is made. It can be cut down and made into other sight blanks as well. It's a great tool for your toolbox you use to be a great gunsmith!  
39.9 39.9 1 EUR
Tuotenro: 100045341
HARRISON DESIGN & CONSULTING RESCUE FRONT SIGHT BLANK, .375 X 65 X .085
Valmistajan tuotenumero: HD013 Ted Yost kehitti ja valmisti näitä tähtäimiä useita vuosia sitten ja pitkän poissaolon jälkeen ne ovat jälleen saatavilla Harrison Designilta. Nämä tähtäimet voi käyttää pelastamaan liukukappaleen väärin leikatuista etutähtäinuratista. Niissä on ylisuuri urapohja, jonka nimellismitat ovat .085" syvyys, .375" leveys 65 asteen urakulmalla. Se on tarpeeksi suuri pelastamaan lähes minkä tahansa tyyppisen epäonnistumisen ja töhrimisen. Terän korkeus on .275", pituus .630" ja leveys .125. Pystysuuntainen rillipinni on jätetty pois, jotta voit sovittaa sen sijainnin mihin tahansa liukukappaleesi reiän sijaintiin. Urabase on .625" leveä, joten sitä voidaan muotoilla liukukappaleesi päälle tai voit leikata sivut haluamaasi ulkonäköön. Terän ja urapohjan liitoskohtaan on koneistettu säde, mikä vahvistaa tähtäintä huomattavasti. Tämä on osa, jonka jokaisen aseasepän tulisi pitää 2-3 kappaletta varastossa, sillä se voi auttaa pulasta, jos virhe sattuu. Sitä voidaan myös leikata ja muokata muihin tähtäinaihioihin. Se on loistava työkalu työkalupakkiisi, jota käytät ollaksesi loistava aseaseppä!
39.9 EUR 3 39,90 € *
Toimitusaika noin 2-4 viikkoa.
3 kpl. USA:n varastossa
Ominaisuudet: Korkeus: .275 Leveys: .125 Merkki: 1911 Outline: None Tyyppi: Blank

Ominaisuudet

Korkeus: .275 Leveys: .125 Outline: None Tyyli: Blank Valmistaja: 1911 Toimituksen paino: 0,009kg Toimituksen korkeus: 13mm Toimituksen leveys: 76mm Toimituksen pituus: 152mm

Tuotekuvaus

Made in USA



Ted Yost developed and made these sights several years ago and after a long absence from the marketplace they are once again available from Harrison Design. These sights can be used to rescue a slide from mis-cut front dovetails. They have an oversize dovetail base featuring nominal dimensions of .085"" depth, .375"" width with a 65 dovetail angle. That's big enough to rescue most any sort of ugliness and butchery. The blade is .275"" tall X .630"" long X .125 wide. The vertical rill pin has been omitted so you can match it's location to wherever your slide's hole location is located. The dovetail base is .625"" wide, so it can be blended to the top of your slide, or youcan cut the sides back for the appearance you want. A radius is machined at the point where the blade joins the dovetail base, strengthening the sight appreciably. This is a part that every gunsmith should keep 2 or 3 of on hand as it can get you out of a jam is a slip up is made. It can be cut down and made into other sight blanks as well. It's a great tool for your toolbox you use to be a great gunsmith!  
Uutiskirje