SMITH ENTERPRISE M14/M1A EXTENDED BOLT STOP - SMITH ENTERPRISE M14 EXTENDED BOLT STOP

Installation was tricky. Ordered a small brass punch and gunsmith hammer before attempting to replace the punch pin from the original bolt lock. Couldn't get the punch pin out far enough and then had to cut it with a dremel cutoff wheel while preventing any damage to the rifle.

Function, and aesthetics are perfect.

Works amazing !!!

Great addition. Easier to find in a rush, or when wearing gloves.

This among the magazine release was of my recent changes and it is well worth it. Ensure you use a 1/16" punch to remove the pin and do so gently. I was able to use the same roll pin and not have to change it by being gentle. Also, I did not take the roll pin all the way out. I moved it enough to release the bolt stop, cleaned the area and spring, then added the new bolt stop and drifted the roll pin back into place. This roll pin, among others, is easily damaged. For me, I had to remove my scope mount prior to installation. I thought it would be possible to do it but was not. This roll pin is under a lot of tension from the receiver. This was completed upon a Springfield M1A Loaded model with all GI parts and an older rifle so it was still made to GI spec.

This product definitely gives an advantage to the stock bolt stop. While it appears a lot larger than the stock part, it does not protrude to snag on things but offers a much more positive engagement surface. Definitely recommend for all M1As no matter their purpose along with the magazine release from Sadlak.

Works as advertised, great at sending the bolt home after a mag change while on the move. Downside is the price and that I had more than a little trouble getting it installed, though I'm not a gunsmith. Other than that I would buy it again.

Yeah, its pricey for a small hunk of metal but it works as described. But anything firearm related is expensive, that's just the way it is. I found installation was very easy. After taping up both sides of the receiver I used a 1/16th punch and that only got me an 1/8th of an inch movement before the punch jammed in the receiver.



I then removed the punch and got a 1/16th Allen wrench that is 4 inches long and cut off the short bent end. Now you have a flexible 4 inch long "punch" that can push out the roll pin out very easily. Small taps on a hammer and within 2 minutes the pin had moved just enough to remove the old stop and insert the new one. Easy as that. The Allen wrench set cost me 4 bucks at Lowes so its no great loss of that wrench size.



I reused the original roll pin as it was already in the receiver hole and pushed it back in to mate with the 2 receiver holes. Of course the spring was inserted in the spring pockets before tapping the roll pin back in.



Push the roll pin towards the rear to remove the old pin and towards the muzzle end and follow these tips and the install will be easy.

This little product took me about 15 minutes to put on my Great Battle Rifle!! Used a little tape and tapped out the roll pin and replaced the OEM part with this great little part!! Makes the Battle Rifle that much meaner and leaner!! One thing, make sure your spring is snapped into the bolt stop when you put it on. If not it could wiggle loose.

This thing is a bit tricky to install but well worth the effort. It will speed up your reloads and if you have any experience with an AR-15/M4 it will feel familiar.

Allows quick closing of the bolt with left hand. Installation is difficult, I broke 3 punches and 2 drill bits just to get the stock pin out. Make sure to use lots of masking tape to protect the receiver. Finish blends in with my Springfield Bush Rifle very well, cost is a little high for this little piece of invention.

Well made product but not designed for polytech clones. It will work but the hole needs to be oversized slightly to allow solid fit and function with factory pin. The supplied pin is to small to fit snug in the receiver.

Nicely made and works great, insert a mag and close the bolt just like an AR with your thumb. I little expensive for such a small thing.

Smith Enterprise did a great job designing this part because it fits exactly under the Generation II receiver-mounted Springfield 6x20 mil-dot scope. It fits perfectly in the opening under the cut-out under the scope mount. Yes, it might be difficult removing the roll pin from the OEM bolt stop, but if one takes the time it comes out just fine. To avoid marring the receiver surface while removing he pin, I found it very helpful to use two or three layers of masking tape over all the surfaces that may be contacted by the tools used to remove the pin. A very small diameter drill bit driven in from the front end of the roll pin hole worked well to assist in removing the pin. I used a brass dowell to drive the pin flush as the final step in the installation. No marring of hte receiver resulted because of the use of a brass dowell and covering vulnerable surfaces with masking tape on the receiver prevented any scuffs when the pin is being removed or re-inserted. I had no problem using the OEM roll pin (the one removed) rather than the new one that came with the part. All this really worked well for me!!!

Just installed this on my SOCOM 16 and love it! As soon as I first got my rifle I thought the bolt catch should've been bigger. This makes it a lot easier to operate the bolt stop. You don't have to search for it with your finger like on the old one! The only bad thing I can say about this is the installation process. You better have a long skinny and tough punch to get that pin out!

The SA factory pin is a few thousandths less in diameter than the pin shipped with the part, so don't attempt to re-use the factory pin. With the proper punches, this is not a difficult retrofit. Results are tremendous, which fits the price! Most impressive is the match of the retro part to the original finish. Kudos to Smith. [...] I would recommend to the unskilled to examine the factory part on dis-assembly, and hone the evident wear marks before installation.

Works like a charm, it looks great and would get one for my next M1A.

Like the others said installation can be a pain, and make sure the pin you use will fit right otherwise you may have operation issues. Only other con is if you lock the bolt to the rear and if you lay the rifle down on the left side, the bolt will release. Could be a pain at the firing range.

Smith Ent. who makes this piece developed it on request by Special Forces I believe. This is a great invention for dropping mags when you are using shooting gloves or wet gloves such as neoprene or dive gloves. There is another one out there by Sadlak I have not tried that looks like it gives even better access. It is on my order this month. These bolt stops are a simple must have change out part. Like everything else Smith Ent. builds, they are high quality. This is a great first enhancement for your M14 if you are just getting started tinkering with your weapon.

I would give this product 5 stars if it weren't so expensive for what it is.

It's a major pain in the butt to install, but that's the fault of the M14/M1A design, not the catch's. Removing the roll pin that holds the factory catch is phenomenally difficult to accomplish without marring the receiver. I punched the pin out as far as I could then used

Once installed it works great and is one of those must-have upgrades for any serious M14/M1A shooter.

Works just like an AR-15 bolt release. Do not use the factory pin on your rifle, I tried to and it's a hair to big. The bolt stop didn't move freely with the factory pin and the spring wasn't strong enough to return the bolt stop if you pulled the charging handle back. Use the pin supplied with the part from brownells it works flawlessly.