Ominaisuudet
- Toimituksen paino: 0,007kg
- Toimituksen leveys: 83mm
- Toimituksen pituus: 146mm
- UPC: 856008005260
Tuotekuvaus
USA:n vientiluvan tyyppi: 0A501.x
Tuotenro: 100007219
Valm.nro: 103-106
856008005260 Tämän sarjan asennus vähentää keskikokoisen J-kehyksen Smith & Wesson -revolverin liipaisimen vetovoimaa yli 12 lbs:sta 9 lbs:iin. Sarja sisältää uuden palautusliukujousen, pääjousen ja Apex XP laukaisinjousisarjan. Asennus ei vaadi sovitusta tai muokkausta tehtaalla oleville jouksille tai osille. Poista vain tehdasosat ja asenna J-kehyksen duty/carry -sarja. Yhteensopiva kaikkien modernien keskikokoisten J-kehyksen revolverien kanssa, joissa on runkoon asennettu laukaisinjousi.Toimitusaika noin 2-4 viikkoa.
APEX TACTICAL SPECIALTIES INC:n J-FRAME DUTY/CARRY KIT on täydellinen valinta kaikille Smith & Wesson J-frame revolverin omistajille, jotka haluavat parantaa aseensa laatuja. Tämä asennussarja vähentää liipaisimen vetopainetta yli 12 lb:sta 9 lb:aan.
Asennus on helppoa: Sarjan asentaminen ei vaadi osien tai jousien muokkaamista. Poista vain tehdasosat ja asenna J-frame duty/carry kit.
Kit toimii kaikkien modernien keskikokoisten J-frame revolverien kanssa, joissa on runkoon asennettu laukaiseva nuppi.
.333 Batting Average 4.9.2016
Bought the spring kit for my new S&W 442. I channeled my inner armorer since being out of the army for nearly 19 years. After installing the new springs, I went to the range to test it out. I had 4 misfires in the first box of 50 cartridges that I shot through it, and the trigger would not return on it's own after being shot. I talked to S&W, who gladly mailed me new OEM main and rebound springs after I unsuccessfully tried to find my originals. Looks like I will be developing a stronger trigger finger.
S&W 638 Installation and Performance 26.7.2014
In all honesty, I was a bit nervous about installing this kit, having never done any trigger work. APEX provided great videos as well as another Youtube video from Terry G titled "S&W Airweight Trigger Job: "The Yoda G Mod". I used APEX's videos for their kit, but I went a bit farther as the Yoda G Mod teaches how to completely dissassemble, remove the cylinder lock, what surfaces can use polishing and which ones not to touch. Replacing the springs is only 2/3 the job, in my opinion. Polishing most of the contact or "friction point" surfaces inside really make a huge difference also and are not hard- took me less than an hour to do the whole install, and that was using the two Apex Youtube videos and the Yoda video. Only issue I had was a small pin fell out in the area of the trigger guard upon complete dissasembly, and it was difficult from the video to tell excactly where that pin went. I found an exploded parts drawing on the internet and it saved the day. No left over parts. I would say double action pull, without using a gauge, decreased from a very hard 12-14 to a much more manageable 8 or so. Again this is subjective as I have no trigger pull gauge, but it is definitely much lighter. The 638 also has single action capability, and it seems to break about 2.5 - 3 lbs. Save yourself some money and buy the kit. A job like I did with the polishing and parts replacement would easily cost $150 or more. Just follow the instructions "exactly" as getting the side-plate off the way they describe is critical as is using the proper size screwdrivers. One tool they recommend for installing a spring, I didn't have, but it was no issue whatsoever. I am not a mechanic, by any means, but probably have average mechanical aptitude. If I can do this, you can do this. God Bless and have a great day!
Kohdattiin virhe tämän sisällön lataamisessa. Päivitä sivu jatkaaksesi. Jos ongelma jatkuu, ota yhteyttä asiakaspalveluumme.