Korisi on tyhjä.

Ostoskori

09-5122933

Tilaa uutiskirje

WOLFF
AR-15/M16 EXTRA-POWER HAMMER SPRING

969000101

Helps Eliminate Common Ignition Problems Great When Using Ammo With Hard Primers

Durable, steel springs provide extra hammer power to ensure proper ignition with each trigger pull. Replaces factory spring. Note: For use in semi-auto models only. Not for use in full auto or burst fire models.

SPECS: Steel. Approximately 23/32" (18.2mm) wide, 2" (5.1cm) long.

Lisää...

Auttaa poistamaan yleisiä syttymisongelmia – Erinomainen kovilla nalleilla varustetun ammuksen kanssa

Kestävät, teräksestä valmistetut jouset tarjoavat lisävoimaa vasaralle varmistaen asianmukaisen syttymisen jokaisella liipaisimen vedolla. Korvaa tehdasjousen. Huom: Käytettäväksi vain puoliautomaattimalleissa. Ei käytettäväksi täysautomaattisissa tai sarjatuli malleissa.

SPECS: Teräs. Noin 23/32" (18.2mm) leveä, 2" (5.1cm) pitkä.

Lisää...

Asiakasarviot: WOLFF HAMMER SPRING, 3-PAK

Arvioiden lukumäärä: 16
Arvostelut brownells.com sivustolla: 16
Arvioiden keskiarvo: 4,7

No more Failure to Fire (13.1.2013)

Eliminate Failure to Fire in 7.62x39 upper with TULAmmo, and Chiappa .22 upper with remington ammo. Had Bushmaster lower parts kits. Heavier hammer was not required

Never misfire again (18.4.2016)

I first tried this spring in a AR 10 I built a few months back and the original would not fire a single factory load. I installed the spring and never misfired again. I had a 5.56 that I built and it occasionally would misfire. So I broke it down in the field and installed the heavy spring and had the same great results. The gun functioned perfict every time.

Made Improvement (4.7.2017)

Helped out my 7.62x39 upper. Just realize a side effect is that the bolt will be harder to pull back. Enough of difference that my wife and kid complain about it.

AF15 with milsurp 5.45 (11.8.2010)

I shoot milsurp 5.45 Russian ammo in my AR-15, and the hard primers caused between 3 to 5 unfired rounds per mag using the stock hammer spring.
This Wolff spring gave me 3 unfired rounds in my last 40 to 50 mags with no other changes.

Does work for AR15 Timney triggers (20.10.2010)

Tried this on my timney trigger after getting light strikes on primers and the spring is too large.

Significant reduction in misfires (2.4.2011)

I was experiencing a 30% misfire rate (6 out of 20) with steel-case ammo in my 7.62x39 custom AR15. Installing this spring helped significantly to reduce misfires.

Heavy Weight Hammer Spring (19.6.2011)

Harder to install because of the heavy spring but works like a champ and something needed for my AR 7.62x39.

Buying another for next build (22.6.2011)

Was having about one out of three "no fires" on my 7.62x39 with steel ammo. This completely cured the problem. Still had a feed problem with all brands of mags, so I alternated brass and steel rounds in my mags, and now all problems gone. Works like it should, no jams or no fires.

Greatly Reduces Lock Time (3.10.2011)

These heavy weight hammer springs greatly reduce lock time in competition rifles. Replace your after market (RRA etc.) hammer spring with one of these. Your scores will go up, especially in off hand!

Great for your .50BMG lower (19.3.2012)

This was exactly what was needed for my lower that I used for a BOHICA .50BMG upper.

Completely fixed my problem! (4.10.2012)

I was having a problem with light strikes when I bought a new upper in 7.62X39. I was using a DPMS lower and some wolf ammo. I know this ammunition has hard primers but my Colt had never had an issue. I replaced the factory spring with this Wolffe heavy weight hammer spring and problem solved!

Reduces lock time. (19.11.2012)

It's physics. If the hammer spring is heavier, the hammer will move more quickly. If you do ANY amount of shooting off-hand/standing/kneeling/sitting (or even prone) past 50 yards, your accuracy will benefit from this hammer spring.

It ever-so-slightly increased the trigger pull on my ALG ACT trigger, but I tried a Tubbs CS trigger spring and a JP reduced-power trigger spring and both combinations brought the trigger pull back down to noticeably lighter than how the trigger came from the factory. The ACT is BUTTER SMOOTH and top-notch. If your trigger is even slightly gritty (most are), you won't even notice a difference in the trigger pull.

I don't have any exact numbers for group sizes, but my group sizes, standing at 50 yards, during my agency's carbine qual shrank considerably when using this hammer spring. The audible 'whack' of the hammer hitting the firing pin/rear of the bolt carrier is noticeably louder using this spring. If your current hammer spring is very worn/weak, you'll even notice the increased strength when you pull on the charging handle.

This also offers insurance against light primer strikes whent he weapon is dirty/fouled. There is no downside. A solid value.

And, it's made from Wolff's proprietary 'rocket wire' steel alloy. They use a special heat-treat process for the metal, after winding the spring. They then coat the surface with a protectant; I've never seen a Wolff spring rust (even when shooting thousands of rounds of corrosive ammo in an AK47/74). It costs more than the el-cheapo parts beacuse YOU'RE GETTING MORE. :)

Fixed CMMG .22LR Conversion Problem (15.5.2013)

I had about 80% of rounds fail to fire using my CMMG .22LR conversion bolt. This spring brought that rate down to around 3%.

Will fix the problem (20.3.2016)

This spring will fix any light strike problem you are having with 7.62x39 AR upper. Tested on many different types of ammo, and none failed to fire after installing. I would also recommend you change out the firing pin to an enhanced firing pin, this combo works.

GOOD PRODUCT, GREAT RESULTS. (3.5.2017)

i HAD PUT TOGETHER AN AR-10 BUT ON A TEST FIRE (USING GERMAN MILITARY SURPLUS AMMO) THE PRIMERS WERE ONLY DIMPLED A BIT. i ORDERED WOLFE HAMMER SPRINGS AND PROBLEM WAS SOLVED. I BOUGHT A COUPLE EXTRA AS BACK UPS OT FOR OTHER FUTURE BUILDS.

SHIPPING WAS ALSO VERY QUICK.

Immediately solved my light strike no pr (23.9.2017)

I built a budget ar and it immediately started misfiring. I put a wolf buffer spring in and this wolf extra strength hammer spring and problem solved. It instantly became completely reliable. No more problems runs like a top.

Lue 16 arvostelua lisää brownells.com sivustolla

11.9 45.9 3 EUR

Tuotenro: 969000101
WOLFF HAMMER SPRING, 3-PAK
Valmistajan tuotenumero: 30094 Kestävät, teräksestä valmistetut jouset tarjoavat lisävoimaa vasaralle varmistaen asianmukaisen syttymisen jokaisella liipaisimen vedolla. Korvaa tehdasjousen. Huom: Käytettäväksi vain puoliautomaattimalleissa. Ei käytettäväksi täysautomaattisissa tai sarjatuli malleissa.

21.9 EUR 0 21,90 € *

Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Ominaisuudet

Valmistaja: AR-15 Toimituksen paino: 0,005kg Toimituksen korkeus: 10mm Toimituksen leveys: 69mm Toimituksen pituus: 132mm

Tuotekuvaus

Made in USA

Tuotenro: 969000100
WOLFF HAMMER SPRING
Valmistajan tuotenumero: 30093 Kestävät, teräksestä valmistetut jouset tarjoavat lisävoimaa vasaralle varmistaen asianmukaisen syttymisen jokaisella liipaisimen vedolla. Korvaa tehdasjousen. Huom: Käytettäväksi vain puoliautomaattimalleissa. Ei käytettäväksi täysautomaattisissa tai sarjatuli malleissa.

11.9 EUR 15 11,90 € *

Toimitusaika noin 2-4 viikkoa.
Yli 10 kpl. USA:n varastossa

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Tuotenro: 969000102
WOLFF HAMMER SPRING, 10-PAK
Valmistajan tuotenumero: 30095 Kestävät, teräksestä valmistetut jouset tarjoavat lisävoimaa vasaralle varmistaen asianmukaisen syttymisen jokaisella liipaisimen vedolla. Korvaa tehdasjousen. Huom: Käytettäväksi vain puoliautomaattimalleissa. Ei käytettäväksi täysautomaattisissa tai sarjatuli malleissa.

45.9 EUR 0 45,90 € *

Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Helps Eliminate Common Ignition Problems Great When Using Ammo With Hard Primers

SPECS: Steel. Approximately 23/32" (18.2mm) wide, 2" (5.1cm) long.

Lisää...

Auttaa poistamaan yleisiä syttymisongelmia – Erinomainen kovilla nalleilla varustetun ammuksen kanssa

SPECS: Teräs. Noin 23/32" (18.2mm) leveä, 2" (5.1cm) pitkä.

Lisää...

Asiakasarviot: WOLFF HAMMER SPRING, 3-PAK

Arvioiden lukumäärä: 16
Arvostelut brownells.com sivustolla: 16
Arvioiden keskiarvo: 4,7

No more Failure to Fire (13.1.2013)

Eliminate Failure to Fire in 7.62x39 upper with TULAmmo, and Chiappa .22 upper with remington ammo. Had Bushmaster lower parts kits. Heavier hammer was not required

Never misfire again (18.4.2016)

Made Improvement (4.7.2017)

Helped out my 7.62x39 upper. Just realize a side effect is that the bolt will be harder to pull back. Enough of difference that my wife and kid complain about it.

AF15 with milsurp 5.45 (11.8.2010)

Does work for AR15 Timney triggers (20.10.2010)

Tried this on my timney trigger after getting light strikes on primers and the spring is too large.

Significant reduction in misfires (2.4.2011)

I was experiencing a 30% misfire rate (6 out of 20) with steel-case ammo in my 7.62x39 custom AR15. Installing this spring helped significantly to reduce misfires.

Heavy Weight Hammer Spring (19.6.2011)

Harder to install because of the heavy spring but works like a champ and something needed for my AR 7.62x39.

Buying another for next build (22.6.2011)

Greatly Reduces Lock Time (3.10.2011)

These heavy weight hammer springs greatly reduce lock time in competition rifles. Replace your after market (RRA etc.) hammer spring with one of these. Your scores will go up, especially in off hand!

Great for your .50BMG lower (19.3.2012)

This was exactly what was needed for my lower that I used for a BOHICA .50BMG upper.

Completely fixed my problem! (4.10.2012)

Reduces lock time. (19.11.2012)

Fixed CMMG .22LR Conversion Problem (15.5.2013)

I had about 80% of rounds fail to fire using my CMMG .22LR conversion bolt. This spring brought that rate down to around 3%.

Will fix the problem (20.3.2016)

GOOD PRODUCT, GREAT RESULTS. (3.5.2017)

Immediately solved my light strike no pr (23.9.2017)

Lue 16 arvostelua lisää brownells.com sivustolla

Muut ostivat

POWER CUSTOM PRE-TRAVEL ADJUSTABLE 10/22® HAMMER & SEAR KIT
RUGER® 10/22® PRE-TRAVEL ADJUSTABLE HAMMER & SEAR KIT

POWER CUSTOM

Varastossa

129,90 € * 69,90 € - 129,90 €*

Suorituskyvyn parannussarjat

3,8

MAGPUL DUST COVERS, BLACK, 3-PAK
AR-15/M16 PMAG MOE M2 DUST COVERS

MAGPUL

Varastossa

12,90 € *

Lippaan varusteet

BROWNELLS ACCU-WEDGE
AR-15/M16 ACCU-WEDGE

BROWNELLS

Voi laittaa jälkitilaukseen

11,90 € *

"Accu-Wedge"t

PRIMARY WEAPONS AR-15 .223 SHIM SET STEEL UNFINISHED
AR-15 .223 SHIM SET

PRIMARY WEAPONS

Varastossa

16,90 € *

Prikat

J P ENTERPRISES AR 308 ENHANCED GAS RING
ENHANCED GAS RING

J P ENTERPRISES

Varastossa

25,90 € * 25,90 € - 26,90 €*

Kaasujärjestelmän osat

Kirjaudu sisään

Unohditko salasanasi?
Rekisteröidy

Some

Sivuillamme

Tuoteryhmät

Tilaaminen

Asiakaspalvelu

Tervetuloa!

Tervetuloa brownells.fi sivustolle. Meillä on Suomen laajin valikoima asesepän tarvikkeita ja työkaluja, aseiden osia, jälleenlatausvälineitä, luoteja, hylsyjä, ammuntavarusteita, optiikkaa ja paljon muuta. Kymmenien tuhansien tuotteiden varasto, josta voit valita itsellesi sopivimmat tuotteet, olitpa sitten ampuja, metsästäjä tai aseseppä.

Tietoa meistä

Ampujat, metsästäjät, asesepät, aseharrastajat ja aseita työssään käyttävät ovat aina voineet kääntyä Brownellsin puoleen etsiessään korkealaatuisia tuotteita, osia, työkaluja, lataustarvikkeita, optiikkaa tai muuta aseisiin liittyvää. Meillä on aina 100% tyytyväisyystakuu!