Ominaisuudet
- Asetyyppi:
Ruger
- Malli:
10/22
- Toimituksen paino: 0,068kg
- Toimituksen korkeus: 10mm
- Toimituksen leveys: 109mm
- Toimituksen pituus: 213mm
Tuotekuvaus
USA:n vientiluvan tyyppi: 0A501.c
Ruger
10/22
Tuotenro: 713122003
Valm.nro: 1022HS
Täydellinen, helppo asentaa -paketti tarkoittaa, että mukautetun, 2-¾ punnan liipaisimen vetämiseen ei vaadita juurikaan aseentekijän taitoja. Vasar ja liipaisin on valmistettu EDM-koneistamalla pitkäkestoisesta hiiliteräksestä, höyryhionta on tehty ja ne on täysin hiottu ja valmisteltu, jotta saat kevyen, puhtaasti katkeavan liipaisimen vedon ilman suurta vaivannäköä. Tarjoaa nopeamman lukkoajan, lyhyemmän liipaisimen matkustuksen ja parannetun tarkkuuden. Paketti sisältää Ronin erikoisjouset, vasaran ja ruostumattomasta teräksestä valmistetut liipaisimen shimmit, jotka auttavat poistamaan liialliset toleranssit, sekä orjapinnan, joka helpottaa uudelleenkokoamista entisestään. EI sovi 10/22® Magnum -kivääreihin.Toimitusaika noin 2-4 viikkoa.
POWER CUSTOMin RUGER® 10/22® HAMMER & SEAR PACKAGE on täydellinen, helppo asentaa -paketti, joka vaatii vain vähän tai ei lainkaan asekorjaustaitoja. Tämä paketti tarjoaa mukautetun, 2-¾ punnan liipaisimen, joka toimii puhtaasti ja tarkasti.
Paketti sisältää:
Tämä paketti ei sovi 10/22® Magnum -kivääreihin.
Huomioithan, että tämä paketti ei sovi 10/22 Magnum -kivääreihin.
Ruger
10/22
Excellent result, excellent value 8.4.2016
This kit was so reasonably priced that I took a chance and bought it. As this was the first time I had taken the trigger apart I took my time and was careful about fitting it but it really was easy and I had it done in about half an hour. The improvement in the trigger pull was brilliant. There was a very small amount of light take up and then the trigger broke cleanly. The pull measured a shade over three pounds on my Lyman trigger pull gauge, but for some unknown reason it felt much lighter. At the range I sat three of my grandchildren ages 10, 12 and 14 behind the 50 yard bench using RWS R50's. The eldest lad shot first, 4 shots in one hole in the ten ring and one shot just a fraction to one side in the 9 ring. The second lad did the same, 4 x 10's and 1 x 9. Then the youngest lad put all five shots in one tiny hole that I could cover with my small fingernail, in the center of the ten ring. They could not have done this with the heavy stock trigger. Is this a perfect trigger ? when I compare it to the most expensive custom trigger on the market, which I also have, it doesn't fall far short. If I score the expensive custom trigger 10/10 then I would score this kit 9/10. It must be the best value for money trigger upgrade out there and in this respect I would give it 10/10.
Gets the job done 3.3.2015
The original triggar pull on a 10/22 is horrible. With this hammer and sear you get the trigger pull down to just over 2 pounds.
Easy to install and a quick fix to make the 10/22 more accurate.
Kohdattiin virhe tämän sisällön lataamisessa. Päivitä sivu jatkaaksesi. Jos ongelma jatkuu, ota yhteyttä asiakaspalveluumme.