Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi
841370117635 296000784
The steel available to us today is of much higher quality than what was available in 1911 when the 1911 pistol was first produced. Improvements to the entire manufacturing process include better alloys, more controlled furnaces, vacuum heat treat, better tooling, and finite element analysis-all of which EGW uses in production. EGW-specific Improvements to the original 1911 Extractor: EGW found that the extractor rides up the relief groove on the ammunition casing with each round fired: this dulls the hook from constantly banging the case, over time tension is lost, leading to a jammed case which adversely affects accuracy. If you experience a loss of tension or must continually retension your extractor, it is time to replace it. EGW fixed all 3 of these problems by reducing the distance from the bolt face to the extractor hook. They found that most hook designs are cut straight at a right angle. They machined theirs at an acute angle so that there is more surface area for the hook to bite into the case. Right angles are a weak point on other extractors so they put radii on both sides of theirs to increase strength. The hook is machined with a special cutter that leaves a nice clean radius in the inside corner where most extractors fail. Lastly EGW extractors are vacuum heat treated yielding great spring properties and the capability to maintain tension for 70,000+ rounds.
69.9 69.9 1 EUR
Tuotenro: 296000784
EGW GI EXTRACTOR IMPROVED .45 ACP SERIES BLUED
Valmistajan tuotenumero: 10322 841370117635 Nykyään käytössämme oleva teräs on paljon korkealaatuisempaa kuin vuonna 1911, jolloin 1911-pistooli valmistettiin ensimmäisen kerran. Valmistusprosessin parannuksiin kuuluvat paremmat seokset, tarkemmin kontrolloidut uunit, tyhjiökarkaisu, parempi työkaluvalikoima ja äärelliselementtimenetelmän hyödyntäminen – kaikkia näitä EGW käyttää tuotannossaan. EGW:n erityiset parannukset alkuperäiseen 1911 Extractoriin: EGW havaitsi, että extractor liikkuu ammuksen hylsyn helpotusuran ylös jokaisen laukauksen yhteydessä: tämä tylsyttää koukkua jatkuvasti osuessaan hylsyyn, ja ajan myötä jännitys menetetään, mikä johtaa jumiutuneeseen hylsyyn ja heikentää tarkkuutta. Jos koet jännityksen menetystä tai sinun täytyy jatkuvasti uudelleenjännittää extractoria, on aika vaihtaa se. EGW korjasi kaikki nämä kolme ongelmaa vähentämällä etäisyyttä lukon kasvosta extractorin koukkuun. He havaitsivat, että useimmat koukkumuotoilut leikataan suoraan oikeassa kulmassa. He koneistivat omansa terävässä kulmassa, jotta koukulla olisi enemmän pinta-alaa tarttua hylsyyn. Oikeat kulmat ovat heikkouskohtia muissa extractoreissa, joten he lisäsivät säteet molemmille puolille omaansa vahvuuden lisäämiseksi. Koukku on koneistettu erikoisleikkurilla, joka jättää kauniin puhtaan säteen sisäkulmaan, jossa useimmat extractorit epäonnistuvat. Lopuksi EGW:n extractorit tyhjiökarkaistaan, mikä antaa niille erinomaiset jousiominaisuudet ja kyvyn ylläpitää jännitystä 70 000+ laukauksen ajan.
69.9 EUR 8 69,90 € *
Toimitusaika noin 2-4 viikkoa.
8 kpl. USA:n varastossa
Ominaisuudet: Merkki: 1911 Viimeistely: Blued

Ominaisuudet

Valmistaja: 1911 Viimeistely: Blued Toimituksen paino: 0,045kg Toimituksen korkeus: 13mm Toimituksen leveys: 114mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA
USA:n vientiluvan tyyppi: 0A501.x



The steel available to us today is of much higher quality than what was available in 1911 when the 1911 pistol was first produced. Improvements to the entire manufacturing process include better alloys, more controlled furnaces, vacuum heat treat, better tooling, and finite element analysis-all of which EGW uses in production. EGW-specific Improvements to the original 1911 Extractor: EGW found that the extractor rides up the relief groove on the ammunition casing with each round fired: this dulls the hook from constantly banging the case, over time tension is lost, leading to a jammed case which adversely affects accuracy. If you experience a loss of tension or must continually retension your extractor, it is time to replace it. EGW fixed all 3 of these problems by reducing the distance from the bolt face to the extractor hook. They found that most hook designs are cut straight at a right angle. They machined theirs at an acute angle so that there is more surface area for the hook to bite into the case. Right angles are a weak point on other extractors so they put radii on both sides of theirs to increase strength. The hook is machined with a special cutter that leaves a nice clean radius in the inside corner where most extractors fail. Lastly EGW extractors are vacuum heat treated yielding great spring properties and the capability to maintain tension for 70,000+ rounds.
Uutiskirje