Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
WALTHER 22 VORTEX VIPER/VENOM SIGHT MOUNT

841370115709 296000654
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
84.9 84.9 1 EUR
Tuotenro: 296000654
EGW WALTHER 1911-22 VORTEX VIPER/VENOM SIGHT MOUNT
Valmistajan tuotenumero: 49302 841370115709 EGW:n punapistetähtäimet on tarkoitettu asennettavaksi vasemmalta oikealle (kun piippu osoittaa eteenpäin). Liukukisko kapenee progressiivisesti helpottaakseen asennusta. Poista vain aseen takatähtäin ja korvaa se EGW:n kiinnityksellä, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter -punapistetähtäimen. Mitään muutoksia ei vaadita. Voit milloin tahansa ottaa kiinnityksen pois ja palauttaa takatähtäimen paikoilleen. Kiinnitystarvikkeet sisältyvät pakkaukseen. Asennusohjeet: Poista takatähtäin* Asenna EGW:n tähtäimen kiinnitys liukukiskoon Kiristä asetuspultti (jos sovellettavissa) Aseta punapistetähtäin EGW:n tähtäimen kiinnitykseen (punapistetähtäimen ja kiinnityksen väliin asetettu pieni paperinpala helpottaa poistoa ja pitää Loctite-liiman poissa punapistetähtäimestä.) Levitä sinistä Loctite-liimaa mukana tulleisiin kiinnityspultteihin Kiristä kiinnityspultit 15 tuumapoundiin 2 kantaista ruuvia - Mukana Vortex Viper ja Venom -tähtäimiä varten 2 tasapäistä ruuvia - Mukana Burris FastFire ja Docter -tähtäimiä varten Mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Aseen muokkaaminen voi mitätöidä valmistajan takuun. Tämän tuotteen tulisi asentaa ja tarkistaa pätevä aseseppä. Vastuuta ei oteta vahingoista tai vammoista, jotka voivat johtua tämän tuotteen virheellisestä asennuksesta tai käytöstä.
84.9 EUR 4 84,90 € *
Toimitusaika noin 2-4 viikkoa.
4 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: P22 Materiaali: Aluminum Merkki: Walther Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: P22 Materiaali: Aluminum Tyyli: Tactical Valmistaja: Walther Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Uutiskirje