EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
EGW Sight Mount Vortex Viper/Venom - Täydellinen valinta S&W M&P:lle
EGW:n punapistekiikarin kiinnitys on suunniteltu asennettavaksi vasemmalta oikealle (mikäli piippu on eteenpäin). Kiinnitysprofiilissa on progressiivinen kapeneminen, joka helpottaa asennusta.
Tuotekuvaus
Poista takakiikari aseestasi ja vaihda se EGW-kiinnitykseen, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter punapistekiikarisi. Kiinnityksen voi irrottaa ja takakiikarin voi vaihtaa milloin tahansa. Asennusmateriaalit sisältyvät pakettiin.
Asennusohjeet
- Poista takakiikari*
- Asenna EGW Sight Mount kiinnityskouruun
- Tiukkaa säätöruuvi (tarvittaessa)
- Aseta punapistekiikari EGW Sight Mountiin (pienellä paperinpalan avulla punapistekiikarin ja kiinnityksen väliin helpotat irrotusta ja estät Loctiten pääsyn punapistekiikariin).
- Levitä sinistä Loctitea mukana tuleville kiinnitysruuveille
- Kiristä kiinnitysruuvit 15in/lbs
Ruuvit
2 kpl kuusiokolo-ruuveja - Mukana Vortex Viper ja Venom kiikareille
2 kpl tasapohjaisia ruuveja - Mukana Burris FastFire ja Docter kiikareille
Kiinnitykseen tarvitaan 5/64'' kuusiokoloavain.
Huomio: Aseesi muokkaaminen voi mitätöidä valmistajan takuun. Tämä tuote tulisi asentaa ja tarkistaa pätevän asekorjaajan toimesta. Ei vastuuta vahingoista tai loukkaantumisista, jotka voivat johtua virheellisestä asennuksesta tai tuotteen käytöstä.
Tämä kiinnitys ei sovi:
- Smith & Wesson M&P C.O.R.E -sarja (jo optiikka valmiina)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson M&P .22 Compact
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE