Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
S&W M&P SHIELD EZ VORTEX VIPER/VENOM SIGHT MOUNT

841370117567 296000652
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Does not work with M&P, M&P 2.0 or M&P 22.
84.9 84.9 1 EUR
Tuotenro: 296000652
EGW S&W M&P SHIELD EZ VORTEX VIPER/VENOM SIGHT MOUNT
Valmistajan tuotenumero: 49292 841370117567 EGW:n punapistetähtäimet on tarkoitettu asennettavaksi vasemmalta oikealle (kun piippu osoittaa eteenpäin). Kisko kapenee progressiivisesti, jotta asentaminen olisi helpompaa. Poista vain aseen takatähtäin ja korvaa se EGW:n kiinnikkeellä, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter -punapistetähtäimen. Voit milloin tahansa ottaa kiinnikkeen pois ja palauttaa takatähtäimen. Asennustarvikkeet sisältyvät pakettiin. Asennusohjeet: Poista takatähtäin* Asenna EGW:n tähtäinkiinnike kiskoon Kiristä kiinnitysruuvi (jos sovellettavissa) Aseta punapistetähtäin EGW:n kiinnikkeelle (punapistetähtäimen ja kiinnikkeen väliin asetettu pieni paperinpala helpottaa irrottamista ja pitää Loctite-liiman pois punapistetähtäimestä.) Levitä sinistä Loctite-liimaa mukana toimitettuihin kiinnitysruuveihin Kiristä kiinnitysruuvit momenttiin 15in/lbs 2 kantaista kateruuvia - Mukana Vortex Viper ja Venom -tähtäimiä varten 2 litteää pääkateruuvia - Mukana Burris FastFire ja Docter -tähtäimiä varten Tämän kiinnikkeen mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Aseen muuttaminen voi mitätöidä valmistajan takuun. Tämän tuotteen tulisi asentaa ja tarkistaa pätevä aseseppä. Vastuuta ei oteta vahingoista tai vammoista, jotka saattavat aiheutua tämän tuotteen virheellisestä asennuksesta tai käytöstä. Ei sovi M&P, M&P 2.0 tai M&P 22 -malleihin.
84.9 EUR 2 84,90 € *
Toimitusaika noin 2-4 viikkoa.
2 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: M&P380 Shield EZ 2.0, M&P9 Shield EZ Materiaali: Aluminum Merkki: Smith & Wesson Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: M&P380 Shield EZ 2.0,M&P9 Shield EZ Materiaali: Aluminum Tyyli: Tactical Valmistaja: Smith & Wesson Väri: Black Toimituksen paino: 0,029kg Toimituksen korkeus: 25mm Toimituksen leveys: 79mm Toimituksen pituus: 133mm

Tuotekuvaus

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Does not work with M&P, M&P 2.0 or M&P 22.
Uutiskirje