Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
S&W 52 VORTEX VIPER/VENOM SIGHT MOUNT

841370113637 296000799
EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Smith & Wesson Model 52 This mount does not fit: Smith & Wesson Model 41
84.9 84.9 1 EUR
Tuotenro: 296000799
EGW S&W 52 VORTEX VIPER/VENOM SIGHT MOUNT
Valmistajan tuotenumero: 49309 841370113637 EGW:n punapistetähtäimet on tarkoitettu asennettavaksi vasemmalta oikealle (kun piippu osoittaa eteenpäin). Urassa on progressiivinen kartio helpottamaan asennusta. Poista vain aseen takatähtäin ja korvaa se telineellä, jotta voit asentaa Vortex Viper/Venomin, Burris FastFiren tai Docterin punapistetähtäimen. Voit milloin tahansa ottaa telineen pois ja palauttaa takatähtäimen. Asennustarvikkeet sisältyvät. Asennusohjeet: Poista takatähtäin* Asenna EGW Tähtäinteline uraan Kiristä kiinnitysruuvi (jos sovellettavissa) Aseta punapistetähtäin EGW Tähtäintelineelle (punapistetähtäimen ja telineen väliin laitettu pieni paperinpala helpottaa irrottamista ja pitää Loctiten poissa punapistetähtäimestä.) Levitä sinistä Loctitea mukana tuleville kiinnitysruuveille Kiristä kiinnitysruuvit momenttiin 15in/lbs 2 Kupukantaruuvia - Mukana Vortex Viper- ja Venom-tähtäimille 2 Litteäkantaruuvia - Mukana Burris FastFire- ja Docter-tähtäimille Mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Aseen muokkaaminen voi mitätöidä valmistajan takuun. Tuotteen tulisi asentaa ja tarkistaa pätevä aseseppä. Vastuuta ei oteta vahingoista tai vammoista, jotka voivat aiheutua tuotteen väärästä asennuksesta tai käytöstä. Tämä teline sopii: Smith & Wesson Malli 52 Tämä teline ei sovi: Smith & Wesson Malli 41
84.9 EUR 2 84,90 € *
Toimitusaika noin 2-4 viikkoa.
2 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: 52 Materiaali: Aluminum Merkki: Smith & Wesson Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: 52 Materiaali: Aluminum Tyyli: Tactical Valmistaja: Smith & Wesson Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Smith & Wesson Model 52 This mount does not fit: Smith & Wesson Model 41
Uutiskirje