Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
RUGER AUTO VORTEX VIPER/VENOM SIGHT MOUNT

841370112951 296000668
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
84.9 84.9 1 EUR
Tuotenro: 296000668
EGW RUGER AUTO VORTEX VIPER/VENOM SIGHT MOUNT
Valmistajan tuotenumero: 49321 841370112951 EGW-pistetähtäimet on tarkoitettu asennettavaksi vasemmalta oikealle (piipun ollessa suunnattuna eteenpäin). Uraleikkaus kapenee edetessään, mikä helpottaa asentamista. Poista vain aseen takatähtäin ja korvaa se EGW-kiinnikkeellä, jotta voit asentaa Vortex Viper/Venom-, Burris FastFire- tai Docter-pistetähtäimen. Voit milloin tahansa irrottaa kiinnikkeen ja palauttaa takatähtäimen paikalleen. Asennustarvikkeet sisältyvät pakkaukseen. Asennusohjeet: Poista takatähtäin* Asenna EGW-tähtäinkiinnike uraleikkaukseen Kiristä kiinnitysruuvi (jos sovellettavissa) Aseta pistetähtäin EGW-tähtäinkiinnikkeelle (pistetähtäimen ja kiinnikkeen väliin asetettu pieni paperinpala helpottaa irrottamista ja pitää Loctiten poissa pistetähtäimestä) Levitä sinistä Loctitea mukana tuleviin kiinnitysruuveihin Kiristä kiinnitysruuvit momenttiin 15in/lbs 2 kantaan upotettua ruuvia - Mukana Vortex Viper- ja Venom-tähtäimille 2 litteää pääruuvia - Mukana Burris FastFire- ja Docter-tähtäimille Tämän kiinnikkeen mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Aseen muokkaaminen voi mitätöidä valmistajan takuun. Tämän tuotteen tulisi asentaa ja tarkistaa pätevä aseseppä. Tuotteemme käytöstä tai väärästä asennuksesta aiheutuvista vahingoista tai vammoista ei oteta mitään vastuuta.
84.9 EUR 4 84,90 € *
Toimitusaika noin 2-4 viikkoa.
4 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: Mark III, Mark I, Mark II, P90, P89, P94, P95, 22/45, Mark IV, P85, P91, P93, P97 Materiaali: Aluminum Merkki: Ruger Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: 22/45,Mark I,Mark II,Mark III,Mark IV,P85,P89,P90,P91,P93,P94,P95,P97 Materiaali: Aluminum Tyyli: Tactical Valmistaja: Ruger Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Uutiskirje