Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi
841370117246 296000787
The EGW Evolved 1911 Sear Spring has been quietly in the works for some time. EGW is known for improving on original designs, one could even say they go through an EVOLUTION. With over 30 years experience in the 1911 market, they have finally come up with their our own fix to combat the typical issues associated with other sear springs. Sometimes 1911 frames can be a bit out of spec. One of the more common issues they have seen is the sear spring slot cut lower than it should be. This can cause the sear spring to not fully engage on the sear. Many springs currently on the market are not long enough to address this issue. EGW went back to the drawing board and made their spring over .030"" longer on the left finger to accommodate frames that encounter this issue. Above Image Details: Detail A - The left side of the spring has a relief cut to allow for the spring to move without contacting or rubbing on the frame. This ensures a smoother, crisper trigger pull. Detail B - The sear pad on the left leaf is less than 1/2 the size and weight than other sear springs, thus reducing the weight for recoil or inertia to act upon. Detail C - The center and right side leaves are 5% narrower to reduce weight and increase feel. Detail D - The disconnector pad on the center leaf is smaller than other sear springs to reduce weight, while still retaining the standard contact. Please Note - they do not glass bead or sandblast the sears after heat treat. The heat treating process leaves the springs with a spotty finish. This is not rust and does not affect performance in any way.  
34.9 34.9 1 EUR
Tuotenro: 296000787
EGW EVOLVED 1911 SEAR SPRING 2PK
Valmistajan tuotenumero: 10692 841370117246 EGW:n kehittämä Evolved 1911 Sear Spring on ollut työn alla jo jonkin aikaa. EGW tunnetaan alkuperäisten suunnitelmien parantelusta, voisi jopa sanoa, että heidän tuotteensa käyvät läpi EVOLUUTION. Yli 30 vuoden kokemuksella 1911-markkinoilla he ovat viimein keksineet oman ratkaisunsa tyypillisiin muihin sear springeihin liittyviin ongelmiin. Joskus 1911-rungot voivat olla hieman epästandardin mukaisia. Yksi yleisimmistä ongelmista, jonka he ovat havainneet, on sear spring -urat leikattu alemmas kuin niiden pitäisi olla. Tämä voi aiheuttaa sen, että sear spring ei kunnolla kytkeydy seariin. Monet markkinoilla olevat jousit eivät ole tarpeeksi pitkiä käsittelemään tätä ongelmaa. EGW palasi piirustuspöydälle ja teki keväästään yli 0,030 tuumaa pidemmän vasemmalla sormella, jotta se sopisi runkoihin, joissa tämä ongelma ilmenee. Yllä olevan kuvan tiedot: Yksityiskohta A - Kevään vasemmalla puolella on helpotusleikkaus, joka mahdollistaa jousen liikkumisen ilman, että se koskettaa tai hankaa runkoa vasten. Tämä takaa sujuvamman, terävämmän liipaisunvedon. Yksityiskohta B - Vasemman lehden sear pad on alle puolet kokoa ja painoa verrattuna muihin sear springeihin, vähentäen näin painoa, johon rekyyli tai inertia voivat vaikuttaa. Yksityiskohta C - Keskimmäisen ja oikeanpuoleisen lehden leveys on 5% kapeampi painon vähentämiseksi ja tuntuman parantamiseksi. Yksityiskohta D - Keskimmäisen lehden disconnector pad on pienempi kuin muissa sear springeissä painon vähentämiseksi, samalla säilyttäen standardikosketuksen. Huomioithan - he eivät lasikuulapuhalla tai hiekkapuhalla seareja karkaisun jälkeen. Karkaisuprosessi jättää jouset täplikkäällä pinnalla. Tämä ei ole ruostetta eikä se vaikuta suorituskykyyn millään tavalla.
34.9 EUR 0 34,90 € *
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Ominaisuudet: Merkki: 1911

Ominaisuudet

Valmistaja: 1911 Toimituksen paino: 0,045kg Toimituksen korkeus: 13mm Toimituksen leveys: 114mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



The EGW Evolved 1911 Sear Spring has been quietly in the works for some time. EGW is known for improving on original designs, one could even say they go through an EVOLUTION. With over 30 years experience in the 1911 market, they have finally come up with their our own fix to combat the typical issues associated with other sear springs. Sometimes 1911 frames can be a bit out of spec. One of the more common issues they have seen is the sear spring slot cut lower than it should be. This can cause the sear spring to not fully engage on the sear. Many springs currently on the market are not long enough to address this issue. EGW went back to the drawing board and made their spring over .030"" longer on the left finger to accommodate frames that encounter this issue. Above Image Details: Detail A - The left side of the spring has a relief cut to allow for the spring to move without contacting or rubbing on the frame. This ensures a smoother, crisper trigger pull. Detail B - The sear pad on the left leaf is less than 1/2 the size and weight than other sear springs, thus reducing the weight for recoil or inertia to act upon. Detail C - The center and right side leaves are 5% narrower to reduce weight and increase feel. Detail D - The disconnector pad on the center leaf is smaller than other sear springs to reduce weight, while still retaining the standard contact. Please Note - they do not glass bead or sandblast the sears after heat treat. The heat treating process leaves the springs with a spotty finish. This is not rust and does not affect performance in any way.  
Uutiskirje