Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
DESERT EAGLE (POST 2017) VORTEX VIPER/VENOM SIGHT MOUNT
EGW:n valmistama sight mount on täydellinen lisävaruste Vortex Viper/Venom, Burris FastFire ja Docter punapisteitä varten. Tämä kestävä ja kevytrakenteinen mount on suunniteltu helposti asennettavaksi.
Tuotteen tiedot:
- Materiaali: 7075 Alumiini
- Pinta: Matte Black Hardcoat
- Kokonaispituus: 1.811"
- Kokonaisleveys: .99"
- Asennusmateriaalit: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
Yhteensopivuus:
- Vortex Viper/Venom
- Burris FastFire
- Crimson Trace CTS-1200, CTS-1300
- Docter
EGW:n punapistesiteet on tarkoitettu asennettavaksi vasemmalta oikealle (muzzle eteenpäin). Dovetail-profiili mahdollistaa helpomman asennuksen. Poista vain aseesi takanäkö ja vaihda se meidän mounttiimme. Muutoksia ei vaadita, ja voit ottaa mountin pois ja vaihtaa takanäön milloin tahansa.
Asennusohjeet:
- Poista takanäkö*
- Asenna EGW Sight Mount dovetailiin
- Kireytä set screw (jos tarpeen)
- Aseta punapistesuunnitelma EGW Sight Mountille (pienellä paperinpalan avulla punapistesuunnitelman ja sight mountin väliin helpotat poistamista ja estät Loctiten pääsyn punapistesuunnitelmaan)
- Käytä sinistä Loctitea mukana tuleviin asennusruuveihin
- Kireytä asennusruuvit 15in/lbs
Huom: Mukana tulevat ruuvit vaativat 5/64'' allen avaimen asennukseen.