Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Esittely: CZ SHADOW 2 VORTEX VIPER/VENOM SIGHT MOUNT
Tuotetiedot:
- Materiaali: 7075 Alumiini
- Päällyste: Matte Black Hardcoat
- Kokonaispituus: 1.811"
- Kokonaisleveys: .99"
- Asennusosat: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
- Red Dot -sovitus: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
EGW:n punapisteet on tarkoitettu asennettavaksi vasemmalta oikealle (mikäli piippu osoittaa eteenpäin). Dovetailissa on progressiivinen kapeneminen helpottamaan asennusta. Poista vain aseesi takasivustat ja vaihda se meidän kiinnikkeeseemme, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter punapisteen. Muutoksia ei vaadita. Voit poistaa kiinnikkeen ja vaihtaa takasivustasi milloin tahansa. Asennusosat sisältyvät.
Asennusohjeet:
- Poista takasivustat*
- Asenna EGW Sight Mount dovetailiin
- Kiristä set screw (jos sovellettavissa)
- Aseta punapiste EGW Sight Mountiin (pienellä paperipalasella punapisteen ja kiinnikkeen väliin laittaminen helpottaa poistamista ja pitää Loctite:n poissa punapisteestä).
- Levitä sinistä Loctite:a mukana toimitettuihin asennusruuveihin
- Kiristä asennusruuvit 15in/lbs
2 Button Head Cap Screws - Mukana Vortex Viper ja Venom Sights -malleille
2 Flat Head Cap Screws - Mukana Burris FastFire ja Docter Sights -malleille
Tämän kiinnikkeen mukana tulevat ruuvit vaativat 5/64'' allen-avainasennusta varten.