Ominaisuudet
- Toimituksen paino: 0,567kg
- Toimituksen korkeus: 91mm
- Toimituksen leveys: 94mm
- Toimituksen pituus: 277mm
- UPC: 757253718014
Tuotenro: 749007261
Valm.nro: 010482
757253718014 Ammuksesi tarkka suorituskyky riippuu täysin sekä luodin että patruunan yhtenäisyydestä. Tämän yhtenäisyyden saavuttaminen ei ole mahdollista ilman tarkkaa ja luotettavaa mittauslaitetta. Forsterin ainutlaatuinen Co-Ax Case & Cartridge Inspector antaa sinulle mahdollisuuden varmistaa yhtenäisyys mittaamalla kolme kriittistä ulottuvuutta: kaulan seinämän paksuus, patruunan kaulan keskeisyys ja luodin poikkeama. Mittaukset ovat tuhannesosien tuumissa, joten tarkkuus on erinomainen. Inspector on ainutlaatuinen, koska se tarkistaa sekä luodin että patruunan kohdistuksen suhteessa koko patruunan tai kotelon keskilinjaan (akseliin). Forsterin Case Inspector käyttää Forster Case Trimmer Pilots -lisävarusteita (myydään erikseen).Toimitusaika noin 2-4 viikkoa.
Ammusten tasalaatuisuuden saavuttaminen ei ole mahdollista ilman tarkkaa ja luotettavaa mittauslaitetta. Forsterin yksinoikeudellinen Co-Ax Case & Cartridge Inspector tarjoaa sinulle mahdollisuuden varmistaa tasalaatuisuus mittaamalla kolme kriittistä ulottuvuutta:
Mittaukset tapahtuvat tuhannesosan tuumaa tarkkuudella, joten tarkkuus on erinomainen. Inspector on ainutlaatuinen, koska se tarkistaa sekä kuulan että kotelon kohdistuksen suhteessa koko patruunan tai kotelon keskilinjaan (akseliin). Forster Case Inspector käyttää Forster Case Trimmer Piloteja (myydään erikseen).
Useful 11.9.2017
I agree with the above review about the difficulty of set up and the V groove. The tool is tedious to setup, and when you change over from checking concentricity to checking T.I.R. it again takes time to get all the adjustments made. It isn't the most efficient process and the tool really can't handle a long cartridge witout the case head compression spring pushing the meplat into the adjustment bar, though it is very useful for checking case neck thickness. I'm not a competitive shooter where I need every little bit of accuracy, but I do like to build very consistent rounds. Knowing what I do now I would have purchased the Sinclair concentricity guage instead
So so tool 28.9.2013
The v groove holder the bullet sits in was very rough from the factory. So much so that within a few turns it was cutting the copper on the bullet. little time with a dremmel and a stone and polish wheel cleaned it up glass smooth and the problem is gone. It takes a little bit to get the tool setup right so all the angles jive but once done it seems to work pretty well. One thing to note though is if the meplat is not perfect you will not get a good measurement. There is a spring that pushes the round against an anvil where the v groove piece above is. This causes the round to wobble a little giving inaccurate measurements if you are not careful. Need to put a little sizing wax on the rear v section where the case rolls to make it smooth.
Overall it works well once you take the time to properly adjust everything but is definitely not a tool for the impatient!
Kohdattiin virhe tämän sisällön lataamisessa. Päivitä sivu jatkaaksesi. Jos ongelma jatkuu, ota yhteyttä asiakaspalveluumme.