Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

AMERICAN TRIGGER CORPORATION
AR-15 AR GOLD TRIGGER CURVED

100004262
Drop-In Fire Control System Gives A Light, Safe, Match-Grade Pull
Self-contained trigger/assembly installs in minutes and delivers a light, smooth, match-grade trigger pull free of grittiness, with an ultra-crisp letoff and short reset. Simply remove factory trigger and safety selector, drop in the module, reinstall selector and pins, and you’re ready to shoot. Completely new engagement geometry produces a light 3-lb. pull and crisp release without compromising reliability or safety. The two-stage design is adjustable for sear engagement, with a first-stage takeup of approximately 6 ounces, followed by actual sear movement taking up the rest of the weight—the reverse of the military two-stage AR trigger pull profile. Instead, the shooter can build force steadily, maintaining precise control and keeping his attention on the target. After release, reset travel is only .030", less than half the .070" typical of standard match triggers, to aid in fast, accurate follow-up shots. The sear captures the hammer at the back instead of near the pivot point to help produce the light pull and maintain safety. A second, independent, intercepting sear is positioned to block the hammer if it slips off the primary sear, as when the weapon is dropped or suffers hard impact. If the intercepting sear captures the hammer, pulling the trigger will still fire the rifle, though with a heavier pull weight. In addition, the Gold system uses the rifle’s factory safety to positively capture the hammer, like an M1 Garand, and roll it back below the primary sear for an extra margin of safety. A lightweight aluminum housing contains the entire system and maintains the correct tolerances between the working parts. The receiver pins serve only to anchor the module in the receiver, with no effect on trigger function.

SPECS: Trigger/Hammer – Wire EDM cut S7 tool steel. Housing – Aluminum, anodized, black. AR Gold fits any mil-spec AR-15 with .154" trigger and hammer pin holes. Will not fit rifles with Colt-type sear block or AR-style .308 rifles.

439.9 439.9 1 EUR
Tuotenro: 100004262
AMERICAN TRIGGER CORPORATION AR GOLD CURVED TRIGGER ADJUSTIBLE
Valmistajan tuotenumero: NONE Itsensä sisältävä liipaisin/kokoonpano asennetaan minuuteissa ja tarjoaa kevyen, pehmeän, kilpatason liipaisunvedon ilman karheutta, erittäin terävällä vapautuksella ja lyhyellä palautuksella. Poista vain tehtaan liipaisin ja turvakytkin, aseta moduuli paikalleen, asenna valitsin ja tapit uudelleen, ja olet valmis ampumaan. Täysin uusi kosketusgeometria tuottaa kevyen 3 paunan vedon ja terävän vapautuksen ilman luotettavuuden tai turvallisuuden vaarantamista. Kahden vaiheen suunnittelu on säädettävissä sear-kosketuksen osalta, ensimmäisen vaiheen esivedolla noin 6 unssia, jonka jälkeen itse sear-liike ottaa loppupainon - päinvastoin kuin sotilaiden kahden vaiheen AR-liipaisunvedon profiili. Sen sijaan ampuja voi kasvattaa voimaa tasaisesti, ylläpitäen tarkkaa hallintaa ja keskittyen maaliin. Vapautuksen jälkeen palautusmatka on vain .030", alle puolet standardin kilpaliipaisimien tyypillisestä .070" matkasta, mikä auttaa nopeissa, tarkoissa jälkiseurantalaakeissa. Sear nappaa vasaran takaa sen sijaan, että se olisi lähellä kääntöpistettä, auttaen tuottamaan kevyen vedon ja ylläpitämään turvallisuutta. Toinen, itsenäinen, väliin tarttuva sear on sijoitettu estämään vasara, jos se liukuu pois pääsearista, kuten aseen pudotessa tai kohdatessa kovan iskun. Jos väliin tarttuva sear nappaa vasaran, aseen liipaisimen vetäminen laukaisee silti aseen, vaikkakin raskaammalla vedolla. Lisäksi Gold-järjestelmä käyttää aseen tehdasturvallisuutta positiivisesti napatakseen vasaran, kuten M1 Garandissa, ja rullatakseen sen takaisin alle pääsearin lisäturvallisuuden vuoksi. Kevyt alumiinikotelo sisältää koko järjestelmän ja ylläpitää oikeita toleransseja työskentelevien osien välillä. Vastaanottimen tapit palvelevat ainoastaan moduulin ankkurointia vastaanottimessa, ilman vaikutusta liipaisimen toimintaan.
439.9 EUR 4 439,90 € *
Toimitusaika noin 2-4 viikkoa.
4 kpl. USA:n varastossa
Ominaisuudet: Merkki: AR-15 Tyyppi: Drop-In

Ominaisuudet

Tyyli: Drop-In Valmistaja: AR-15 Toimituksen paino: 0,181kg Toimituksen korkeus: 58mm Toimituksen leveys: 114mm Toimituksen pituus: 180mm

Tuotekuvaus

Made in USA
USA:n vientiluvan tyyppi: 0A501.c



Drop-In Fire Control System Gives A Light, Safe, Match-Grade Pull
Self-contained trigger/assembly installs in minutes and delivers a light, smooth, match-grade trigger pull free of grittiness, with an ultra-crisp letoff and short reset. Simply remove factory trigger and safety selector, drop in the module, reinstall selector and pins, and you’re ready to shoot. Completely new engagement geometry produces a light 3-lb. pull and crisp release without compromising reliability or safety. The two-stage design is adjustable for sear engagement, with a first-stage takeup of approximately 6 ounces, followed by actual sear movement taking up the rest of the weight—the reverse of the military two-stage AR trigger pull profile. Instead, the shooter can build force steadily, maintaining precise control and keeping his attention on the target. After release, reset travel is only .030", less than half the .070" typical of standard match triggers, to aid in fast, accurate follow-up shots. The sear captures the hammer at the back instead of near the pivot point to help produce the light pull and maintain safety. A second, independent, intercepting sear is positioned to block the hammer if it slips off the primary sear, as when the weapon is dropped or suffers hard impact. If the intercepting sear captures the hammer, pulling the trigger will still fire the rifle, though with a heavier pull weight. In addition, the Gold system uses the rifle’s factory safety to positively capture the hammer, like an M1 Garand, and roll it back below the primary sear for an extra margin of safety. A lightweight aluminum housing contains the entire system and maintains the correct tolerances between the working parts. The receiver pins serve only to anchor the module in the receiver, with no effect on trigger function.

SPECS: Trigger/Hammer – Wire EDM cut S7 tool steel. Housing – Aluminum, anodized, black. AR Gold fits any mil-spec AR-15 with .154" trigger and hammer pin holes. Will not fit rifles with Colt-type sear block or AR-style .308 rifles.

Uutiskirje