Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

WILSON COMBAT
AR-15 EJECTION PORT COVER PARTS KIT ONLY

810025500283 965900019
Quality replacement dust cover rod, c-clip and torsion spring for AR style rifles.   Changing them is very easy, but care must be taken to not lose the c-clips and to reassemble it correctly. Please read and follow the instructions below to get your new cover installed and ready to go: Push the hinge pin forward until you can see the little "c" clip, positioning it so the open end is toward you. Using small punches or a screw driver, very carefully push on each end of the clip until it pops off. It doesn't take much, so take it slow and easy. Force should not be required; the clip will be under the pin and easily removed. You can use tweezers, or a magnetic pickup, or carefully tilt the receiver until the clip comes out in your hand. Be careful it is small and is easily lost. Make note of the cover spring position. If you don't have a diagram, take a picture so you can put it back right later. Slide the hinge pin rearward, covering the spring with your hand so it is not lost when the tension is released. Keep working the rod rearward until it is clear. Go slow so you don't scratch your upper receiver. Installation is mostly reversing the above. An easy way to install the hinge pin spring is to position it with the short leg to the rear of the receiver, pointing up toward the ejection port. Push the hinge pin into the spring a bit. Grab the front part of the spring, lifting it away from the receiver and press the long leg down, allowing it to rest against the ejection port cover. Slide your hinge pin in the rest of the way. Line up the little slot on the hinge pin with the front wall of the hinge pin channel. Use the wall to slide the clip down against the pin and use a punch to push it into place. You'll hear an audible click as it engages properly.
12.9 12.9 1 EUR
Tuotenro: 965900019
WILSON COMBAT AR-15 EJECTION PORT COVER PARTS KIT ONLY
Valmistajan tuotenumero: TREPDK 810025500283 Laadukas varaosasarja AR-tyylisiin kivääreihin sisältäen pölykannen tangon, C-kiinnikkeen ja vääntöjousen. Niiden vaihtaminen on helppoa, mutta on tärkeää olla varovainen, ettei C-kiinnikkeitä hukkaa ja että osat kootaan oikein. Lue ja noudata alla olevia ohjeita uuden kannen asentamiseksi ja käyttövalmiiksi saamiseksi: Työnnä saranatappia eteenpäin kunnes näet pienen "C"-kiinnikkeen ja aseta se niin, että avoin pää on sinua kohti. Käytä pieniä työntimiä tai ruuvimeisseliä ja työnnä varovasti kiinnikkeen kumpaakin päätä, kunnes se irtoaa. Se ei vaadi paljon voimaa, joten etene hitaasti ja varovasti. Voimaa ei tarvita; kiinnike on tapin alla ja se poistetaan helposti. Voit käyttää pinsettejä tai magneettinostinta tai kallistaa varovasti vastaanotinta, kunnes kiinnike putoaa käteesi. Ole varovainen, se on pieni ja katoaa helposti. Pane merkille pölykannen jousen asento. Jos sinulla ei ole kaaviota, ota kuva, jotta voit koota sen oikein myöhemmin. Työnnä saranatappi taaksepäin ja peitä jousi kädelläsi, jotta se ei katoa, kun jännitys vapautuu. Jatka tangon työntämistä taaksepäin, kunnes se on vapaa. Etenet hitaasti, jotta et naarmuta ylävastaanotinta. Asennus on pääasiassa käänteinen edellä mainittuun. Helppo tapa asentaa saranatapin jousi on asettaa se lyhyellä jalalla vastaanottimen taakse, osoittaen ylöspäin poistoaukkoa kohti. Työnnä saranatappia hieman jousta vasten. Tartu jousen etuosaan, nosta sitä pois vastaanottimesta ja paina pitkä jalka alas, anna sen levätä poistoaukon kannen päällä. Työnnä saranatappisi loppuun asti. Aseta tapin pienen uran kohdalle vastaanottimen saranatappikanavan etuseinämän kanssa. Käytä seinämää työntääksesi klipsiä alas tapia vasten ja käytä työntimiä työntääksesi sen paikalleen. Kuulet selvän napsahduksen, kun se kiinnittyy oikein.
12.9 EUR 121 12,90 € *
Toimitusaika noin 2-4 viikkoa.
Yli 10 kpl. USA:n varastossa
Ominaisuudet: Merkki: AR-15

Ominaisuudet

Valmistaja: AR-15 Toimituksen paino: 0,033kg Toimituksen korkeus: 19mm Toimituksen leveys: 102mm Toimituksen pituus: 203mm

Tuotekuvaus

Made in USA
USA:n vientiluvan tyyppi: 0A501.x



Quality replacement dust cover rod, c-clip and torsion spring for AR style rifles.   Changing them is very easy, but care must be taken to not lose the c-clips and to reassemble it correctly. Please read and follow the instructions below to get your new cover installed and ready to go: Push the hinge pin forward until you can see the little "c" clip, positioning it so the open end is toward you. Using small punches or a screw driver, very carefully push on each end of the clip until it pops off. It doesn't take much, so take it slow and easy. Force should not be required; the clip will be under the pin and easily removed. You can use tweezers, or a magnetic pickup, or carefully tilt the receiver until the clip comes out in your hand. Be careful it is small and is easily lost. Make note of the cover spring position. If you don't have a diagram, take a picture so you can put it back right later. Slide the hinge pin rearward, covering the spring with your hand so it is not lost when the tension is released. Keep working the rod rearward until it is clear. Go slow so you don't scratch your upper receiver. Installation is mostly reversing the above. An easy way to install the hinge pin spring is to position it with the short leg to the rear of the receiver, pointing up toward the ejection port. Push the hinge pin into the spring a bit. Grab the front part of the spring, lifting it away from the receiver and press the long leg down, allowing it to rest against the ejection port cover. Slide your hinge pin in the rest of the way. Line up the little slot on the hinge pin with the front wall of the hinge pin channel. Use the wall to slide the clip down against the pin and use a punch to push it into place. You'll hear an audible click as it engages properly.
Uutiskirje