Korisi on tyhjä.

Ostoskori

09-5122933

Tilaa uutiskirje

HARFORD ENGRAVING SERVICES
AR-15/M16 ENGRAVED EJECTION PORT COVERS

100005626

Engraved Slogans Personalize Your Rifle

Ejection port covers are engraved with colorful slogans to personalize your AR in a unique way. The engraving is on the inside of the cover, so when it’s closed, your gun retains its stock appearance. These are top-quality, all-steel covers made to the correct dimensions for proper fit and function on any mil-spec upper receiver.

SPECS: 1045/1055 cold-rolled carbon steel, Parkerized, black. Comes with detent and detent spring installed; hinge pin, spring, snap ring required (sold separately). AR-15 fits standard .223/5.56mm AR-15/M16 upper receivers. Not for use on Rock River Arms 9mm or Uramex .22 LR.

Lisää...

Kaiverretut Iskulauseet Personoivat Kiväärisi

Laukaisuportin kannet on kaiverrettu värikkäillä iskulauseilla, joiden avulla voit personoida AR-kiväärin ainutlaatuisella tavalla. Kaiverrus on kannen sisäpuolella, joten kun se on kiinni, aseesi säilyttää vakio ulkonäkönsä. Nämä ovat huippulaatuisia, kaikki teräksestä valmistettuja kansi, jotka on tehty oikeiden mittojen mukaan sopimaan ja toimimaan kaikissa mil-spec ylävastaanottimissa.

TEKNISET TIEDOT: 1045/1055 kylmävalssattu hiiliteräs, parkerisoitu, musta. Mukana tulee pidätin ja pidättimen jousi asennettuna; saranatappi, jousi, lukkorengas vaaditaan (myydään erikseen). AR-15 sopii standardin .223/5.56mm AR-15/M16 ylävastaanottimiin. Ei käytettäväksi Rock River Arms 9mm tai Uramex .22 LR:ssä.

Lisää...

Asiakasarviot: HARFORD ENGRAVING SERVICES AR-15 "DON'T TREAD ON ME"/U.S. FLAG

Arvioiden lukumäärä: 57
Arvostelut brownells.com sivustolla: 57
Arvioiden keskiarvo: 4,4

Very impresive!! (25.12.2010)

Great piece, very cool!! Easy to install and works well.

simple and amazing addition, priced well (9.2.2013)

Perfect addition for any AR, its fun and gets the point across. Look this helpfull video by snareman95 up *Replacing AR-15 ejection port dust cover - EASY!!!* on you tube, it'll save you a world of trouble. Took me and the wife 3min at best.

very nice product (26.1.2011)

Very nice engraving, easy to install. Inexpensive way to personalize your rifle without making permanent modifications

Cover is very scratched, but functional (5.1.2013)

It's not acceptable cosmetically if you want something that looks good. But it's functional and the engraving is fine. However, the finish on the cover is covered with scratches.

Nice Finishing Touch (26.12.2011)

This adds a nice finishing touch on a rifle or carbine build. Many positive comments from others admiring the firearm.

looks great (26.3.2012)

really makes the rifle look great

It's for looks. (3.6.2012)

Other than for the looks it does the same as your original ejector port. Good compliments from friends and co-workers though.

Semper Fi (28.7.2017)

This thing went on an AR pistol build. Looks great and functions great. Would recommend to everyone.

Really cool bling for your rifle. (24.2.2016)

Adds a touch of class to the rifle Oohrah

Great Product (1.9.2011)

[...]Ok this fit with no problem at all on my Smith&Wesson M&P I had it on in about 5 mins,looks great and adds a little character to my AR. I would caution to make sure you put something under your rifle, the little clip can be very easy to lose when switching out the covers.

AR-15 "Dead Men Tell No Tales"/Jolly Rog (2.11.2011)

Looks great on my AR-15

Great quality product! (23.2.2012)

It looked great right out of the box. Shipping was faster than expected. It was a fairly easy install I did it myself with minimal tools. Though I did run into a problem taking the pin out of the stock ejection port cover I had to remove the free floating rail to get the pin out which is no problem with the product itself just a little extra work but was well worth it. Its a nice personal touch to my AR15. Very happy with the results.

Nice Engraving... (13.6.2013)

I really wasn't sure what to expect with this. Some reviews had it as junk while others praised it. My cover came with excellent engraving. Clear and centered nicely on the cover. The finish feels rugged and has texture, seems like it will hold up over time. I gave it four stars only because mine, like others who have reviewed this product, came with noticeable blemishes on the "closed" side. Nothing to cry over but worth noting. That's good stuff!

A Little Bling For Your AR (17.9.2010)

A nice little touch for the AR. It should be noted that the pin is secured with the world's smallest snap ring. I made sure to have an extra on hand in case the original went flying into oblivion.

Perhaps the option of a sound chip playing the theme from the movie "300" should be offered as well.

Great Idea (14.10.2010)

Here are some other ones I'd like to see
Farewell Forever = Aeternum Vale
Love of Country = Amor Patriae

Both Latin phrases

Nice Touch (22.12.2011)

Easy to Install and high OE quality type cover. have bought three more (different slogans) for other brothers on my team since

Does what it's suppose to and looks good (15.9.2016)

Installed and functions how it should. I only gave it 4 stars because the etching isn't as visible as some others I've gotten from other sites. Still high quality and is a nice subtle addition.

A nice custom touch (10.9.2010)

Very simple to install, functions just like the original. A great finishing touch to a custom rifle.

Totally Frivolous - And Totally Funny (19.12.2010)

Just a total waste of money on something you just can't live, or shoot without. One of the top items for frivolous spending. I wish I had more AR's so I can get the whole set. Great Christmas gift(s).

A thing of beauty (4.3.2011)

This is the baddest ejection port ever made.

Awesome (13.4.2011)

This dust cover is simply cool. It adds that custom touch to my AR and everone who sees it loves it. It took about 10 min to install, very easy. If you are unsure how to do it there are a few examples on youtube.

Cool addition (26.4.2011)

Part came as described. After initial cleaning, I was very pleased with the resolution of the engraved image. Installation was not complicated (about 5-10 minutes using care not to lose the small Ejection Port Cover Retaining Ring). I'd recommend using small hemostats and/or small dental scraping tool to remove this ring.

We don't retreat! (19.5.2011)

We carry the line of engraved covers and are mostly impressed with them, this one however is a great disappointment. The American Flag is in retreat on this cover, when it is corrected, I will give it 5 stars.

Great piece, adds some personality. (13.2.2012)

The only reason I didn't give this item a 5 was because of the clarity of the item. In other words, you can't see the image that easily. But it's still a great piece. Only word of caution, be careful when taking off your C-clamp, those things love to fly and don't like to let you know where they're going!

308 "Don't Tread on Me" US Flag (9.4.2012)

Looks great on my rifle! It really is a nice little feature to help my rifle stand out and it describes me perfectly! I plan on buying another one for another AR build I have. I would HIGHLY recommend it to anyone, the etchings are nice and clean and it just looks great!

Flag NOT in retreat as stated elsewhere (21.5.2012)

This is a great piece of work. The flag is "flying correctly" per proper hanging and showing the American flag. Blue field left!
NOT IN RETREAT as stated by another uninformed reviewer.
It just go's to show you:
"YOU DON'T KNOW WHAT YOU DON'T KNOW!

Installed on VLTOR MUR1A Upper (10.11.2012)

Note: (you will need to file a little off each side when installing on a VLTOR MUR1A Upper Reciever)But thats not the covers fault because I checked it on a A1 and a Dpms Flat top and it was a perfect fit. The engraving is very nice. As for the orientaion of the Flag. It is correct as per 4 USC Â§ 1-10. I believe the previous reviewer (flag retreat) is confused with the difference between a left and or right shoulder flag Patch.

Great accessory (25.11.2016)

OEM quality. Looks great. Engraving could be brighter, whatever you are shooting at won't know the difference. Not easy to install unless you use a small needle point pliers to hold the small end of the spring down and maintain tension while inserting the rod. If not you will shoot yourself or through the rifle out the window.

Engraved dust over (19.1.2017)

Engraving is very well done, but quality of parkerized finish is so poor I will not put it on my rifle.

Awesome (10.9.2010)

It's a good product, the engraving could be better quality. But all in all it's very nice.

Rock your AR! (4.10.2010)

I am in law enforcement and when the guys on the range saw this they loved it! Great idea to personalize your AR. Adds the American kick but feel to your rifle! Easily replaces existing cover and looks the same until you fire! Wish there was a was a way to have the "you'll only die tired" bigger.

A Must Have!!! (4.1.2011)

this is a Total Must Have, very easy to install and give your gun that personal touch.

Dust Cover... (13.4.2011)

Great conversational piece, easy to install, and adds that personalized touch to any AR. Wish the engraving stood out more, but otherwise a great addition. If you have a beefed up rifle, its a must have.

Easy enough (13.6.2011)

Install was flawless for an M&P15. Only con for me was the lettering for "you'll die tired" is very small.

Ingraving unempressive (8.10.2011)

The engraving is very light, and looks like it was scratched in using a hand engraver. I have good eyesight, and I can barely read the writing.

Thought it would fit. (7.1.2012)

The stock cover measures 3.295 on my DPMS .308. The one I received measures 3.135 so it will fit but it might keep out chainsaw size wood chips. There are BIG GAPS on both sides which makes it look like it is made for smaller rifle. Its cool though I'll put it in the safe.

Works fine (6.6.2012)

Works fine when you order the correct part for the correct gun...brainiac

Wish it would latch properly (18.9.2012)

This port cover is sleek looking and the cover itself is every bit as sturdy as any I've seen. The problem I've had is the ballbearing that keeps the cover latched closed. This one has a tendency to slip which results in the cover opening when I don't want it to. Moving it around on the gun bench or even setting it down by the buttstock in the safe has opened it.

Great quality and fun for the range! (16.10.2010)

Not the easiest to install because of all the small parts (ie, C Clamp). Make sure you have a diagram in front of you! Other than that a 5min install and the fellas got a good laugh at the range...Also adds a little distinction among all of those M4's at the range...-AB88

Looks good but... (27.12.2010)

Semi-easy to install with an extra set of hands[...]My only beef is that the engraving is almost so light that some of it is illegible and after wiping it to see if it was just oil in the letters it looked like I wiped away the H in HUNTER.For the price and cool factor, I'm giving it 4 stars. Quality of part is 5 stars, engraving is not. On the plus side, I guess the engraving won't be too reflective.

ROCKS! (30.12.2010)

A great conversational piece at the range. My brothers got a kick out of it since we all have our zombie plans. Only draw back is having to remove the barrel nut to install.

Not bad (31.12.2010)

Good product. Came out looking BA. Just be careful with the retention C-clip when installing.

Stag Arms AR-15's port doorS flip up (4.1.2011)

Keep in mind that, although this product fits all or most models of AR-15s, the Stag Arms models' (left and/or right handed)port doors flip up, not down. If you decide to purchase this item, the words engraved on the door will not only read in the opposite direction as any other brand AR-15, but will also read upside down. You also may have to remove the gas block assembly on the upper to get the hinge pin removed to attach the door. Better hope the fashion police catch you hanging upside down when you make those crucial zombie kills.

Great Product (15.2.2011)

This is a great littgle addition to my AR, gets alot of compliments at the range. Very easy to install, and if you get hung up you can atch the video here at Brownells!!

Great product. (25.2.2011)

People complain that you have to remove the block then the handguards and the delta ring. But actually you don't. If people knew what they were doing instead of just going by what everyone else says, it would be a better project. Let me tell you from 8 years of gunsmithing. The ejection port cover pin is slightly flexible and so is the ejection port cover. You can slowly and carefully push off the C-clamp and run it out the other side while holding it carefully. Don't make things harder than it really is.

Having Fun... (20.3.2011)

The part fits perfect. Adds a little humor while at the range. Love it!

stag arms right handed vs left handed (6.4.2011)

there was a comment about the stag arms door flipping up the right handed models all of them flip down and the left handed models flip up so only on the left handed models will it read upside down

fits good (6.5.2011)

A good fit on S&W M&P15s does take a few min with small E-clip but take time and do it right. Got this one for mine and "dont run you'll die tired" for the wife. The ingraving is a little light on some of the letters but it is a small area to do it in. They get good comments and some laughs at the range/training

A favorite & easy mod.! (22.5.2011)

Keep oils out of etching,much easier to read (rubbing alcohol on door after cleaning weapon.Tip on clip install, hold with tweezers, & push on (at center) w sharp knife blade.Goes right on with only 2 hands, but entertains many more!LOVE IT!

Easy install (13.6.2011)

Installation is a breeze on a Bushmaster Carbon15. Make sure you get an extra spring and C-clip here also, I sent a clip flying on my first install.

Very Good Item (30.9.2011)

This item came exactly as advertised. It fit perfectly and works as expected.

Adds some style to your weapon (8.12.2011)

Pretty easy to install but like others said just be careful with the C clip (its tiny)..the hardest part was deciding on which port cover I wanted

sweet (7.7.2012)

nice lil touch for ARs. went on easy and looks great. letters are ethched n the metal and not just painted on

Fit great, looks great. (28.12.2012)

Used this on my PSA A3 stripped upper, fits great. The etching is nice and crisp, adds a little personality that I wanted.

Great AR Eye Candy! Looks Great! (19.1.2013)

I specifically ordered the "Zombie Hunter" ejection port cover to review for my blog fans and followers. When I ordered this part, I was in the process of building my newest rifle. My theme for this rifle was the "ultimate zombie killer" and decided to build it in 300 Blackout.

I had already ordered and installed the EOTech "Zombie Stopper" optic from Brownells and a few other zombie related items. I was looking for something that would set my rifle apart from others out there. I was browsing Brownells website and stumbled onto these ejection port covers. This was exactly what I was looking for!

When I ordered this cover, I also ordered the "Don't Tread On Me" and "Join or Die" covers as well. When they arrived, I was surprised to see just how crisp and clear the engravings really were. They really stand out and look great. Installation was a breeze and only took about 10 minutes for each rifle.

I installed the "Zombie Hunter" cover on my Blackout, the "Don't Tread On Me" cover on my competition rifle and the "Join or Die" cover on my SBR. After I was all finished I couldn't have been happier. Not only do they look great but they really add a little something extra to all of my rifles. I plan to order a few more that are offered here and maybe even install one on my work rifle.

Since I have installed the covers on my rifles, I have got nothing but positive comments from other shooters I meet at matches and at the local ranges. If you are looking for something that won't break the bank but really adds something special to your rifle, pick up a few of these covers! You will not be disappointed!

-Michael Sapp
Owner of Lock-N-Load Blog

Eye Catching (12.12.2013)

Received my order a day early and love it. Good quality, engraving looks great. Installed easily in about 15 minutes.

Great service, fast shipping and good product. Will buy again!

My Long Range Zombie Zapper (18.1.2014)

I used a Sun Devil lower that is marked 'Safe â Zombies', so this was just a 'must have' for my new build. It's my long range build - .264 LBC with a 24" bull barrel - don't want those buggers to get too close now.
As with all Brownells products, it is of very high quality. Crisp and well defined engraving. Had it installed with in 10 minutes of receiving it. Looks great.

Lue 57 arvostelua lisää brownells.com sivustolla

16.9 16.9 1 EUR

Tuotenro: 100005626
HARFORD ENGRAVING SERVICES AR-15 "DON'T TREAD ON ME"/U.S. FLAG
Valmistajan tuotenumero: NONE Laukaisuportin kannet on kaiverrettu värikkäillä iskulauseilla, joiden avulla voit personoida AR-kiväärin ainutlaatuisella tavalla. Kaiverrus on kannen sisäpuolella, joten kun se on kiinni, aseesi säilyttää vakio ulkonäkönsä. Nämä ovat huippulaatuisia, kaikki teräksestä valmistettuja kansi, jotka on tehty oikeiden mittojen mukaan sopimaan ja toimimaan kaikissa mil-spec ylävastaanottimissa.

16.9 EUR 0 16,90 € *

Ilmoita saatavuudesta

Loppu varastosta. Saatavuus ei tiedossa.

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Ominaisuudet

Valmistaja: AR-15 Toimituksen paino: 0,045kg Toimituksen leveys: 83mm Toimituksen pituus: 146mm

Tuotekuvaus

Made in USA
USA:n vientiluvan tyyppi: 0A501.x

Engraved Slogans Personalize Your Rifle

Lisää...

Kaiverretut Iskulauseet Personoivat Kiväärisi

Lisää...

Asiakasarviot: HARFORD ENGRAVING SERVICES AR-15 "DON'T TREAD ON ME"/U.S. FLAG

Arvioiden lukumäärä: 57
Arvostelut brownells.com sivustolla: 57
Arvioiden keskiarvo: 4,4

Very impresive!! (25.12.2010)

Great piece, very cool!! Easy to install and works well.

simple and amazing addition, priced well (9.2.2013)

very nice product (26.1.2011)

Very nice engraving, easy to install. Inexpensive way to personalize your rifle without making permanent modifications

Cover is very scratched, but functional (5.1.2013)

It's not acceptable cosmetically if you want something that looks good. But it's functional and the engraving is fine. However, the finish on the cover is covered with scratches.

Nice Finishing Touch (26.12.2011)

This adds a nice finishing touch on a rifle or carbine build. Many positive comments from others admiring the firearm.

looks great (26.3.2012)

really makes the rifle look great

It's for looks. (3.6.2012)

Other than for the looks it does the same as your original ejector port. Good compliments from friends and co-workers though.

Semper Fi (28.7.2017)

This thing went on an AR pistol build. Looks great and functions great. Would recommend to everyone.

Really cool bling for your rifle. (24.2.2016)

Adds a touch of class to the rifle Oohrah

Great Product (1.9.2011)

AR-15 "Dead Men Tell No Tales"/Jolly Rog (2.11.2011)

Looks great on my AR-15

Great quality product! (23.2.2012)

Nice Engraving... (13.6.2013)

A Little Bling For Your AR (17.9.2010)

Great Idea (14.10.2010)

Here are some other ones I'd like to see
Farewell Forever = Aeternum Vale
Love of Country = Amor Patriae

Both Latin phrases

Nice Touch (22.12.2011)

Easy to Install and high OE quality type cover. have bought three more (different slogans) for other brothers on my team since

Does what it's suppose to and looks good (15.9.2016)

Installed and functions how it should. I only gave it 4 stars because the etching isn't as visible as some others I've gotten from other sites. Still high quality and is a nice subtle addition.

A nice custom touch (10.9.2010)

Very simple to install, functions just like the original. A great finishing touch to a custom rifle.

Totally Frivolous - And Totally Funny (19.12.2010)

A thing of beauty (4.3.2011)

This is the baddest ejection port ever made.

Awesome (13.4.2011)

Cool addition (26.4.2011)

We don't retreat! (19.5.2011)

Great piece, adds some personality. (13.2.2012)

308 "Don't Tread on Me" US Flag (9.4.2012)

Flag NOT in retreat as stated elsewhere (21.5.2012)

Installed on VLTOR MUR1A Upper (10.11.2012)

Great accessory (25.11.2016)

Engraved dust over (19.1.2017)

Engraving is very well done, but quality of parkerized finish is so poor I will not put it on my rifle.

Awesome (10.9.2010)

It's a good product, the engraving could be better quality. But all in all it's very nice.

Rock your AR! (4.10.2010)

A Must Have!!! (4.1.2011)

this is a Total Must Have, very easy to install and give your gun that personal touch.

Dust Cover... (13.4.2011)

Easy enough (13.6.2011)

Install was flawless for an M&P15. Only con for me was the lettering for "you'll die tired" is very small.

Ingraving unempressive (8.10.2011)

The engraving is very light, and looks like it was scratched in using a hand engraver. I have good eyesight, and I can barely read the writing.

Thought it would fit. (7.1.2012)

Works fine (6.6.2012)

Works fine when you order the correct part for the correct gun...brainiac

Wish it would latch properly (18.9.2012)

Great quality and fun for the range! (16.10.2010)

Looks good but... (27.12.2010)

ROCKS! (30.12.2010)

A great conversational piece at the range. My brothers got a kick out of it since we all have our zombie plans. Only draw back is having to remove the barrel nut to install.

Not bad (31.12.2010)

Good product. Came out looking BA. Just be careful with the retention C-clip when installing.

Stag Arms AR-15's port doorS flip up (4.1.2011)

Great Product (15.2.2011)

This is a great littgle addition to my AR, gets alot of compliments at the range. Very easy to install, and if you get hung up you can atch the video here at Brownells!!

Great product. (25.2.2011)

Having Fun... (20.3.2011)

The part fits perfect. Adds a little humor while at the range. Love it!

stag arms right handed vs left handed (6.4.2011)

there was a comment about the stag arms door flipping up the right handed models all of them flip down and the left handed models flip up so only on the left handed models will it read upside down

fits good (6.5.2011)

A favorite & easy mod.! (22.5.2011)

Easy install (13.6.2011)

Installation is a breeze on a Bushmaster Carbon15. Make sure you get an extra spring and C-clip here also, I sent a clip flying on my first install.

Very Good Item (30.9.2011)

This item came exactly as advertised. It fit perfectly and works as expected.

Adds some style to your weapon (8.12.2011)

Pretty easy to install but like others said just be careful with the C clip (its tiny)..the hardest part was deciding on which port cover I wanted

sweet (7.7.2012)

nice lil touch for ARs. went on easy and looks great. letters are ethched n the metal and not just painted on

Fit great, looks great. (28.12.2012)

Used this on my PSA A3 stripped upper, fits great. The etching is nice and crisp, adds a little personality that I wanted.

Great AR Eye Candy! Looks Great! (19.1.2013)

Eye Catching (12.12.2013)

Received my order a day early and love it. Good quality, engraving looks great. Installed easily in about 15 minutes.

Great service, fast shipping and good product. Will buy again!

My Long Range Zombie Zapper (18.1.2014)

Lue 57 arvostelua lisää brownells.com sivustolla

Muut ostivat

BROWNELLS M4 BUFFER SPRING (CS)
AR-15/M16 BUFFER SPRINGS

BROWNELLS

Varastossa

11,90 € * 11,90 € - 29,90 €*

Rekyylijouset

ERGO GRIPS AR-15/M16 M4 RECEIVER CASTLE NUT
AR-15 RECEIVER EXTENSION CASTLE NUT

ERGO GRIPS

Varastossa

16,90 € *

Bufferituubien varusteet

BROWNELLS AR-15 EJECTION PORT COVER SPRING
AR-15 EJECTION PORT COVER SPRING

BROWNELLS

Varastossa

6,90 € *

Hylsynpoistoaukon suojan osat

ZRO DELTA AR-15 LOWER PARTS BUILDER KIT
AR-15 LOWER PARTS KIT

ZRO DELTA

Varastossa

49,90 € *

Alarungon osasarjat

2,9

GLOCK PISTOOLIEN LÄPINÄKYVÄT LIPPAAT - 17 PATRUUNAA 9 mm Luger

17 PATRUUNAA 9 mm Luger
GLOCK PISTOOLIEN LÄPINÄKYVÄT LIPPAAT

ELITE TACTICAL SYSTEMS GROUP

Ei saatavilla

Lippaat

3,4

Kirjaudu sisään

Unohditko salasanasi?
Rekisteröidy

Some

Sivuillamme

Tuoteryhmät

Tilaaminen

Asiakaspalvelu

Tervetuloa!

Tervetuloa brownells.fi sivustolle. Meillä on Suomen laajin valikoima asesepän tarvikkeita ja työkaluja, aseiden osia, jälleenlatausvälineitä, luoteja, hylsyjä, ammuntavarusteita, optiikkaa ja paljon muuta. Kymmenien tuhansien tuotteiden varasto, josta voit valita itsellesi sopivimmat tuotteet, olitpa sitten ampuja, metsästäjä tai aseseppä.

Tietoa meistä

Ampujat, metsästäjät, asesepät, aseharrastajat ja aseita työssään käyttävät ovat aina voineet kääntyä Brownellsin puoleen etsiessään korkealaatuisia tuotteita, osia, työkaluja, lataustarvikkeita, optiikkaa tai muuta aseisiin liittyvää. Meillä on aina 100% tyytyväisyystakuu!