Professionally And Easily Replace Stripped-Out Bushing Holes-No Welding Or Drilling
Easily and professionally solves the problem of stripped out stock bushing holes. Special tap cleans out stripped frame threads, cuts new ones without pre-drilling. Matching bushing screws right in, uses original grip screw. Will save your life when polishing/bluing, accurizing .45's!
SPECS: Bushings - .255"-60, blued steel. Tap - High speed.
Lisää...
Ammattimaisesti ja helposti vaihda kuluneet holkkiholkit - Ei hitsausta tai porausta
Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
SPECS: Bushings - .255"-60, sinistetty teräs. Tap - Korkean nopeuden.
Lisää...
Asiakasarviot: BROWNELLS 1911 AUTO OVERSIZED BUSHING TAP
Arvioiden lukumäärä: 8
Arvostelut brownells.com sivustolla: 8
Arvioiden keskiarvo: 4,5
This tap is not for amateurs(26.3.2011)
I am very dissapointed in the results of using this tool. I followed instructions and was very careful to keep everything aligned. The bushing installed with this tool were cocked. This makes it hard to put the pistol grips on and the bushing threads will probably get buggered again because of not being seated properly.Not to mentioned I screwed up a new Kimber TLE .45 receiver.
The problem is that the hole size of the standard bushing is .235 and the tip of the tap is .240 inches. This means you will not get traction till you're 3/4 way through the hole and by that time you will not be aligned perpendicular. The final hole size for the bushing is .255 inches.
The solution is to make the tip of the tap to be about .230 inche not .240. If you don't have a drill press using this tool you are not going to like the results.
Worked fine(1.5.2012)
The tap worked fine. Used it on a Kimber CDP in hand tap wrench. Bushings screwed in tight and square. Had no problem getting it started through the existing hole.
A Good Product And Worth The Money(8.5.2014)
Easy to use in a 1/4" tap wrench. I had to replace grip bushings in my Springfield Champion. This Oversized Grip Bushing Tap worked very well. Easy to do job. It strips the old threads out , then makes new ones. Good to have in the gunsmithing tools.
works just fine(2.6.2011)
I had a grip bushing strip out on a Kimber Pro Carry - I had neglected to check the bushings regularly for tightness and paid the price. A tip on re-tapping without getting the hole crooked: Cut out a 1" by 1" block from a .75" board. Drill a hole (with a drill-press) in the block just big enough for the tap to pass through without wiggling around. Use the block as a guide to keep the tap perpendicular to the frame of the gun while re-tapping. Holding the block in place with finger pressure was easy for an aluminum frame. For a steel frame that is a little harder to get the tap started into, a C clamp may be required to hold the block steady. One last thing - for an aluminum frame 1911 I wouldn't recommend staking the bushing after install, as the bushing itself is harder than the frame and it can still work loose in time. A SMALL amount of JB Weld holds the bushing in place for good, while leaving the bushing and threads undamaged for future removal if necessary.
Great tool!(23.5.2015)
I used this kit on my Kimber Pro CDP II. Worked very well! Chucked bit in hand-held T handle. Using a small block of wood with a perpendicular hole drilled through it the size of the tap, helps to keep the tap at 90 degrees to the work surface.
When I describe myself as a Gunsmith, I mean AMATURE gunsmith. So when I say "easy to use" it's easy.
Perfect tool/bushing solution!(17.4.2017)
I have a Kimber Raptor that came from the factory with a cross-threaded grip bushing, discovered when the grip came loose after about 100 rounds. I tried getting the original bushing back in correctly, thought it held but then it just broke loose again next trip to the range.
I was pretty concerned I'd have to send the thing back to Kimber to get fixed up until I found this oversize tap/bushing set. The PERFECT solution, super easy to use with some care as people people noted to keep the tap going straight. With this aluminum frame gun it cut nice new threads in minutes.
Adding to the others tips, I used a bit of Loctite instead of JB Weld, hopefully that holds, but the intent is the same since the bushing is actually harder than the frame I didn't think staking it was a good idea. Also, I'd screw in the bushing just with fingers, no tools, to make sure you don't accidentally cross-thread it. These threads are so so very fine it would be easy to do, and especially with an aluminum frame easy to damage those new threads. I put it in finger-tight until it bottoms out then use a screwdriver to cinch it up.
Thanks Brownells!
Great solution for stripped bushing(24.6.2017)
Extremely easy to use. Reluctant at first to attempt to repair a stripped out grip bushing on my 1911. Great product.
Back in action(12.9.2017)
Had 2 stripped grip bushings (discovered when I went to install my grip). Ordered this off others reviews, and was NOT disappointed. 2 holes tapped, new bushings installed and grips installed in less than 15 minutes (by hand. Tapped the old holes with a hand tap and this bit). Works like a charm if you have stripped GI bushings!!!
Tuotenro: 080598225 BROWNELLS 1911 AUTO OVERSIZED BUSHING TAP Valmistajan tuotenumero: 41539 Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
64.9EUR2164,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Erikoishana puhdistaa kuluneet kehyksen kierteet ja leikkaa uudet ilman esiporausta.
Holkki ruuvataan suoraan sisään käyttäen alkuperäistä kahvan ruuvia, mikä pelastaa tilanteen kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita.
Materiaali: sinistetty teräs, holkkien koko: .255"-60, hana: korkean nopeuden.
Tuotenro: 080570000 BROWNELLS 1911 BASIC OVERSIZED BUSHING SET 4 BUSHINGS & 1 TAP Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
79.9EUR5179,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Tuotenro: 080571100 BROWNELLS 1911 DELUXE OVERSIZED BUSHING SET 24 BUSHINGS & 1 TAP Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
144.9EUR1144,90 €
*
Toimitusaika noin 2-4 viikkoa. 1 kpl. USA:n varastossa
Tuotenro: 080572025 BROWNELLS 1911 45 CALIBER OVERSIZED STOCK BUSHINGS 24 PACK Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
109.9EUR2109,90 €
*
Toimitusaika noin 2-4 viikkoa. 2 kpl. USA:n varastossa
Tuotenro: 080572050 BROWNELLS 1911 45 CALIBER OVERSIZED STOCK BUSHINGS 48 PACK Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
179.9EUR1179,90 €
*
Toimitusaika noin 2-4 viikkoa. 1 kpl. USA:n varastossa
Tuotenro: 080572012 BROWNELLS 1911 45 CALIBER OVERSIZED STOCK BUSHINGS 4 PACK Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
32.9EUR032,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Professionally And Easily Replace Stripped-Out Bushing Holes-No Welding Or Drilling
Easily and professionally solves the problem of stripped out stock bushing holes. Special tap cleans out stripped frame threads, cuts new ones without pre-drilling. Matching bushing screws right in, uses original grip screw. Will save your life when polishing/bluing, accurizing .45's!
SPECS: Bushings - .255"-60, blued steel. Tap - High speed.
Lisää...
Ammattimaisesti ja helposti vaihda kuluneet holkkiholkit - Ei hitsausta tai porausta
Ratkaisee ammattimaisesti ja helposti ongelman, joka koskee kanta-aseen hylsyn reikien kierteiden kulumaan. Erikoishana puhdistaa kuluneet kehyksen kierteet, leikkaa uudet ilman esiporausta. Vastaava holkki ruuvataan suoraan sisään, käyttäen alkuperäistä kahvan ruuvia. Pelastaa tilanteesi kun kiillotat/sinisöit tai tarkkuusparantelet .45-kaliiperisia aseita!
SPECS: Bushings - .255"-60, sinistetty teräs. Tap - Korkean nopeuden.
Lisää...
Asiakasarviot: BROWNELLS 1911 AUTO OVERSIZED BUSHING TAP
Arvioiden lukumäärä: 8
Arvostelut brownells.com sivustolla: 8
Arvioiden keskiarvo: 4,5
This tap is not for amateurs(26.3.2011)
I am very dissapointed in the results of using this tool. I followed instructions and was very careful to keep everything aligned. The bushing installed with this tool were cocked. This makes it hard to put the pistol grips on and the bushing threads will probably get buggered again because of not being seated properly.Not to mentioned I screwed up a new Kimber TLE .45 receiver.
The problem is that the hole size of the standard bushing is .235 and the tip of the tap is .240 inches. This means you will not get traction till you're 3/4 way through the hole and by that time you will not be aligned perpendicular. The final hole size for the bushing is .255 inches.
The solution is to make the tip of the tap to be about .230 inche not .240. If you don't have a drill press using this tool you are not going to like the results.
Worked fine(1.5.2012)
The tap worked fine. Used it on a Kimber CDP in hand tap wrench. Bushings screwed in tight and square. Had no problem getting it started through the existing hole.
A Good Product And Worth The Money(8.5.2014)
Easy to use in a 1/4" tap wrench. I had to replace grip bushings in my Springfield Champion. This Oversized Grip Bushing Tap worked very well. Easy to do job. It strips the old threads out , then makes new ones. Good to have in the gunsmithing tools.
works just fine(2.6.2011)
I had a grip bushing strip out on a Kimber Pro Carry - I had neglected to check the bushings regularly for tightness and paid the price. A tip on re-tapping without getting the hole crooked: Cut out a 1" by 1" block from a .75" board. Drill a hole (with a drill-press) in the block just big enough for the tap to pass through without wiggling around. Use the block as a guide to keep the tap perpendicular to the frame of the gun while re-tapping. Holding the block in place with finger pressure was easy for an aluminum frame. For a steel frame that is a little harder to get the tap started into, a C clamp may be required to hold the block steady. One last thing - for an aluminum frame 1911 I wouldn't recommend staking the bushing after install, as the bushing itself is harder than the frame and it can still work loose in time. A SMALL amount of JB Weld holds the bushing in place for good, while leaving the bushing and threads undamaged for future removal if necessary.
Great tool!(23.5.2015)
I used this kit on my Kimber Pro CDP II. Worked very well! Chucked bit in hand-held T handle. Using a small block of wood with a perpendicular hole drilled through it the size of the tap, helps to keep the tap at 90 degrees to the work surface.
When I describe myself as a Gunsmith, I mean AMATURE gunsmith. So when I say "easy to use" it's easy.
Perfect tool/bushing solution!(17.4.2017)
I have a Kimber Raptor that came from the factory with a cross-threaded grip bushing, discovered when the grip came loose after about 100 rounds. I tried getting the original bushing back in correctly, thought it held but then it just broke loose again next trip to the range.
I was pretty concerned I'd have to send the thing back to Kimber to get fixed up until I found this oversize tap/bushing set. The PERFECT solution, super easy to use with some care as people people noted to keep the tap going straight. With this aluminum frame gun it cut nice new threads in minutes.
Adding to the others tips, I used a bit of Loctite instead of JB Weld, hopefully that holds, but the intent is the same since the bushing is actually harder than the frame I didn't think staking it was a good idea. Also, I'd screw in the bushing just with fingers, no tools, to make sure you don't accidentally cross-thread it. These threads are so so very fine it would be easy to do, and especially with an aluminum frame easy to damage those new threads. I put it in finger-tight until it bottoms out then use a screwdriver to cinch it up.
Thanks Brownells!
Great solution for stripped bushing(24.6.2017)
Extremely easy to use. Reluctant at first to attempt to repair a stripped out grip bushing on my 1911. Great product.
Back in action(12.9.2017)
Had 2 stripped grip bushings (discovered when I went to install my grip). Ordered this off others reviews, and was NOT disappointed. 2 holes tapped, new bushings installed and grips installed in less than 15 minutes (by hand. Tapped the old holes with a hand tap and this bit). Works like a charm if you have stripped GI bushings!!!