Korisi on tyhjä.

Ostoskori

09-5122933

Tilaa uutiskirje

Tarvitsetko_apua_iso

KNS PRECISION, INC. AR-15/M16 NON-ROTATING PIN SET

.154" Non-Rotating Pins

Tuotenro: 923000036 851876003004 923000036

Kuvaus
Arviot (17)

Precision-Machined To Upgrade Your Existing Hammer & Trigger Pins; Available Standard & Oversized

Redesigned hammer pin and anti-rotation links provide the strongest possible system to eliminate pin rotation, and will withstand the additional force exerted by 9mm conversions and suppressed .223 upper receivers. Helps prevent wear to receiver holes, which is especially important for increasingly-valuable M16 and pre-ban receivers. Notched hammer pin locks into slots in the anti-rotation links; trigger is secured with locking screws, and includes lube ports so adequate lubrication reaches the trigger. Anti-rotation links fit on the outside of the receiver to prevent all movement. Pins are CNC-machined, centerless ground for uniformity and heat treated for durability. Available in Standard .154", Oversized .155", and .170" for larger receivers. Oversized Pins help improve accuracy and trigger control by tightening up any trigger slack that may exist in worn or new receivers. Standard-sized pins drop-in and require no modification to the receiver; oversized pins require the use of the 3.95mm Reamer (available separately).

SPECS: 416 stainless steel pins. .900” (22.8mm) long, .154" (3.91mm), .155" (3.93mm), or .170" (4.31mm) diameter. Set includes (1) hammer pin, (1) trigger pin, (2) screws, (2) anti-rotation links, hex wrenches, and installation tool. Anti-Rotation Links - Steel, Parkerized finish. Retaining Screws - Steel, black oxide finish.

Lisää...

Asiakasarviot: .154" Non-Rotating Pins

Arvioiden lukumäärä: 17
Arvostelut brownells.com sivustolla: 17
Arvioiden keskiarvo: 4,9

Stop walking in it's tracks (6.11.2009)

Very easy to install with no extra tools needed. Stops pin walking and slack at the same time for better shots.

Look at description not picture (27.2.2012)

This kit comes .1555 pins, the side plates and screws, NOT the slightly larger pins and reamer as pictured. I used this to tighten up a JP trigger that was installed in an old receiver that had at one time had oversized pins. The slop made for an inconsistent trigger pull. The KNS kit took care of it, but don't expect miracles. If you are doing a new build and have spec trigger parts, save your money - this won't do much for you.

Works well... (26.6.2017)

I am a certified AR-15 / M-16 Armorer and work as an armorer for my police department. I purchased this pin set for a carbine build I am doing. packaging was okay (plastic bag) but came with no instructions other then a poor picture. installed nicely with no problems. quality is good. I only gave 4 stars to to lack of instructions to install.

Great product (16.12.2009)

If you are adding A drop in trigger this is a must. Over 2000 rounds with no problems.

Very Pleased (5.3.2010)

Put this on my Smith and Wesson M&P. Works great and gives the carbine a custom look to boot.

Outstanding item! (17.7.2010)

Works exceptionally well, installed on my LE M4, full auto and burst with no problems. The pins no longer slip out! Extremely easy to install!

Excellent (29.7.2010)

Easy installation and if you have trouble there is a good youtube video over it done by KNS. Great Product

Excellent product, no problems (2.5.2011)

I mounted these to a Doublestar lower receiver with a Jard trigger. Superb!

I prefer these over JP anti-rotating pins.

Wow much better then stock pins (26.1.2012)

I replaced the stock trigger, hammer pines in a Rock River lower with a Timmney 3lbs dropin trigger , man what a differance just changing the pines. I have the ultimate woodchock trigger now.Also did wonders for S&W 15-22 wow. you can,t go wrong with these.

Well designed and look great (6.3.2012)

Probably the best non rotating pins around. I shortened them slightly so there was no gap between receiver and the locking plates. Very nice

A must to have if you like your rifle (22.4.2012)

This is one of those products that they actually thought it through. Installation is fast and simple. If you are replacing existing pins, just push the existing pins out with the new pins. fast, simple and will save the lower reciever from excessive wear. noticably improves the trigger feel also. They are pricey for PINS but in the long run, worth every dime. They look great,extremely well made, are funtional, and will add value to your rifle.

Worth it (4.8.2012)

These pins cleaned up my trigger pull more than I would have thought they would. All the typical AR grittiness is gone, creep is almost gone. Trigger has a lighter feel as a result. Should significantly improve the reliability/durability of the rifle. Look cool too. Absolutely worth the money.

You should try these pins (24.7.2013)

I have several sets of KNS pins and they are an excellent and easy way to eliminate most of the creep in standard triggers. As a gunsmith and Law Enforcement armorer I highly recommend them for standard triggers and I even use them with Rock River 2-stage triggers. Don't use with Geissele triggers, but they improve everything else.

Piece a Cake!! (4.12.2014)

Bought the Gen 2 recently and gave it 5 stars. So, on this build project I thought of throwing this one on. Again, it was a piece of cake. Really simple. It makes the rifle even look a tougher.

KNS 154" NR Pin Set (31.3.2016)

This is a must have item I believe, it is very easy to install. It looks great on the lower & holds trigger in place 100% of the time. This is a great item and I have used a lot of them, they are a really great product.

Gambled w/ geissele ssa-e and fit (23.9.2017)

I have a m&p 15 sport 2 with geissele ssa-e trigger and still had some wiggle/slop in the pins. Now all the Q&A says they don't work with this brand of trigger. Worked in my case when installed. Nice snug fit. tip I can give you is trigger pin start from right to left. Worked better in my situation. Then do the hammer pin. Kns pins did exactly what they were designed to do. No more slop/ wiggle with these pins!!!!!

Worked with my AR10 PSA gen2 lower (9.11.2017)

Installs easy and the screws came with dried up thread locker. Installed a Rise Armament trigger assembly and locked that in my AR10 receiver.

Lue 17 arvostelua lisää brownells.com sivustolla

60.3 60.3 2 EUR

923000036
.154" Non-Rotating Pins
Valmistajan tuotenumero: NRTHP154 851876003004 . 154" pyörimätön nastat

60.3 EUR 0 60,30 € *

Voi laittaa jälkitilaukseen.

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Rajoitukset

USA vientirajoitus voimassa USA:n hallitus kontrolloi näitä tuotteita. Niiden vienti USA:sta on sallittu vain siihen maahan, johon ne on tilattu, ja vain vastaanottajan tai loppukäyttäjän käyttöön. Niitä ei saa uudelleenmyydä, siirtää tai luovuttaa mihinkään muuhun maahan tai muulle henkilölle kuin vastaanottajalle tai loppukäyttäjälle, ei alkuperäisessä muodossaan eikä muiden tuotteiden osana, ilman etukäteen hankittua lupaa USA:n hallitukselta tai muuta USA:n lakiin ja määräyksiin perustuvaa hyväksyntää.

This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.

Ominaisuudet

Valmistaja: AR-15

Tuotekuvaus

Made in USA
ECCN: I(h)

923000040
.155" Non-Rotating Pins
Valmistajan tuotenumero: NRTHP1555 851876003226 . 155" pyörimätön nastat

60.3 EUR 7 60,30 € *

Varastossa, toimitusaika 1-2 viikkoa.

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Kuvaus
Arviot (17)

Precision-Machined To Upgrade Your Existing Hammer & Trigger Pins; Available Standard & Oversized

Lisää...

Asiakasarviot: .154" Non-Rotating Pins

Arvioiden lukumäärä: 17
Arvostelut brownells.com sivustolla: 17
Arvioiden keskiarvo: 4,9

Stop walking in it's tracks (6.11.2009)

Very easy to install with no extra tools needed. Stops pin walking and slack at the same time for better shots.

Look at description not picture (27.2.2012)

Works well... (26.6.2017)

Great product (16.12.2009)

If you are adding A drop in trigger this is a must. Over 2000 rounds with no problems.

Very Pleased (5.3.2010)

Put this on my Smith and Wesson M&P. Works great and gives the carbine a custom look to boot.

Outstanding item! (17.7.2010)

Works exceptionally well, installed on my LE M4, full auto and burst with no problems. The pins no longer slip out! Extremely easy to install!

Excellent (29.7.2010)

Easy installation and if you have trouble there is a good youtube video over it done by KNS. Great Product

Excellent product, no problems (2.5.2011)

I mounted these to a Doublestar lower receiver with a Jard trigger. Superb!

I prefer these over JP anti-rotating pins.

Wow much better then stock pins (26.1.2012)

Well designed and look great (6.3.2012)

Probably the best non rotating pins around. I shortened them slightly so there was no gap between receiver and the locking plates. Very nice

A must to have if you like your rifle (22.4.2012)

Worth it (4.8.2012)

You should try these pins (24.7.2013)

Piece a Cake!! (4.12.2014)

Bought the Gen 2 recently and gave it 5 stars. So, on this build project I thought of throwing this one on. Again, it was a piece of cake. Really simple. It makes the rifle even look a tougher.

KNS 154" NR Pin Set (31.3.2016)

Gambled w/ geissele ssa-e and fit (23.9.2017)

Worked with my AR10 PSA gen2 lower (9.11.2017)

Installs easy and the screws came with dried up thread locker. Installed a Rise Armament trigger assembly and locked that in my AR10 receiver.

Lue 17 arvostelua lisää brownells.com sivustolla

Muut ostivat
Vaihtoehtoja

Maxima 2-Piece Base Ruger® 10/22® Silver
MAXIMA 2-PIECE STEEL BASES

WARNE MFG. COMPANY

Tätä tuotetta ei voi valitettavasti tilata.

Kiväärien jalustat

0 (0)

2.0 Comb Raising Kit Black
2.0 COMB RAISING KIT

BEARTOOTH PRODUCTS

Voi laittaa jälkitilaukseen Voi laittaa jälkitilaukseen.

40,40 € * 40,40 € - 41,90 €*

Yleiset perälevyt

0 (0)

ACRAGLAS GEL 4 oz. Kit, Non-Flammable
BROWNELLS ACRAGLAS GEL PETAUSSARJA

BROWNELLS

Varastossa Varastossa, toimitusaika 1-2 viikkoa.

59,00 € * 25,80 € - 270,30 €*

Petaus ja liimat

5 (10)

Smith & Wesson M&P 15-22 Magazine 22lr 25rd Polymer Black
SMITH & WESSON M&P 15-22 MAGAZINE 22LR

SMITH & WESSON

Varastossa Varastossa, toimitusaika 1-2 viikkoa.

44,70 € * 43,00 € - 44,70 €*

Lippaat

4,6 (9)

Sale

Multi Post Front Sight Pack Steel Black
AR-15 POST FRONT SIGHT PACK

KNS PRECISION, INC.

Varastossa, toimitusaika 1-2 viikkoa. Varastossa, toimitusaika 1-2 viikkoa.

46,50 € *

Aiempi hinta 54,70 €

Etutähtäimet

4 (2)

Kirjaudu sisään

Unohditko salasanasi?
Rekisteröidy

Some

Sivuillamme

Tuoteryhmät

Tilaaminen

Asiakaspalvelu

Tervetuloa!

Tervetuloa brownells.fi sivustolle. Meillä on Suomen laajin valikoima asesepän tarvikkeita ja työkaluja, aseiden osia, jälleenlatausvälineitä, luoteja, hylsyjä, ammuntavarusteita, optiikkaa ja paljon muuta. Kymmenien tuhansien tuotteiden varasto, josta voit valita itsellesi sopivimmat tuotteet, olitpa sitten ampuja, metsästäjä tai aseseppä.

Tietoa meistä

Ampujat, metsästäjät, asesepät, aseharrastajat ja aseita työssään käyttävät ovat aina voineet kääntyä Brownellsin puoleen etsiessään korkealaatuisia tuotteita, osia, työkaluja, lataustarvikkeita, optiikkaa tai muuta aseisiin liittyvää. Meillä on aina 100% tyytyväisyystakuu!

Hintoihin sisältyy ALV, toimitus aina 10€ per tilaus.

Perinteinen näkymä

Mobiilinäkymä