Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
WALTHER PPQ M2 LEUPOLD DELTAPOINT PRO SIGHT MOUNT

841370116850 296000543
Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Bushnell RXS-100 Crimson Trace CTS-1500 Holosun 407K* Holosun 507K* Holosun EPS-GR* Holosun EPS-RD* Holosun EPS-Carry-GR* Holosun EPS-Carry-RD* Jpoint Leupold Delta Point Pro Optima Redfield Accelerator Shield RMS Shield RMSc Shield SMS Sig Romeo Zero EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
84.9 84.9 1 EUR
Tuotenro: 296000543
EGW WALTHER PPQ M2 LEUPOLD DELTAPOINT PRO SIGHT MOUNT
Valmistajan tuotenumero: 49394 841370116850 Materiaali: 7075 Alumiini Pinnoite: Mattamusta Hardcoat Kokonaispituus: 1.811" Kokonaisleveys: .99" Kiinnitystarvikkeet: (2) 6-32 Button Head -ruuvit, (2) 6-32 Flat Head -ruuvit, (1) 6-32 Set Screw Punapistetähtäimen yhteensopivuus: Bushnell RXS-100 Crimson Trace CTS-1500 Holosun 407K* Holosun 507K* Holosun EPS-GR* Holosun EPS-RD* Holosun EPS-Carry-GR* Holosun EPS-Carry-RD* Jpoint Leupold Delta Point Pro Optima Redfield Accelerator Shield RMS Shield RMSc Shield SMS Sig Romeo Zero EGW:n punapistetähtäimet asennetaan vasemmalta oikealle (kun aseen suuaukko on eteenpäin suunnattuna). Liukupiikki on progressiivisesti kapeneva, mikä helpottaa asennusta. Poista vain aseen takatähtäin ja korvaa se meidän kiinnikkeellämme, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter punapistetähtäimen. Muutoksia ei tarvita. Voit milloin tahansa ottaa kiinnikkeemme pois ja asentaa takatähtäimen takaisin. Kiinnitystarvikkeet sisältyvät. Asennusohjeet Poista takatähtäin* Asenna EGW Sight Mount liukupiikkiin Kiristä set screw (jos sovellettavissa) Aseta punapistetähtäin EGW Sight Mountille (punapistetähtäimen ja kiinnikkeen väliin laitettu pieni paperinpala helpottaa poistamista ja pitää Loctiten poissa punapistetähtäimestä.) Levitä sinistä Loctitea mukana tuleviin kiinnitysruuveihin Kiristä kiinnitysruuvit 15in/lbs vääntömomenttiin 2 Button Head Cap -ruuvit - Mukana Vortex Viper ja Venom tähtäimille 2 Flat Head Cap -ruuvit - Mukana Burris FastFire ja Docter tähtäimille Mukana tulevat ruuvit vaativat 5/64'' allen-avainta asennukseen.
84.9 EUR 0 84,90 € *
Ilmoita saatavuudesta
Ei saatavilla.
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: PPQ M2 Materiaali: Aluminum Merkki: Walther Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: PPQ M2 Materiaali: Aluminum Tyyli: Tactical Valmistaja: Walther Väri: Black Toimituksen paino: 0,227kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 127mm

Tuotekuvaus

Made in USA



Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Bushnell RXS-100 Crimson Trace CTS-1500 Holosun 407K* Holosun 507K* Holosun EPS-GR* Holosun EPS-RD* Holosun EPS-Carry-GR* Holosun EPS-Carry-RD* Jpoint Leupold Delta Point Pro Optima Redfield Accelerator Shield RMS Shield RMSc Shield SMS Sig Romeo Zero EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Uutiskirje