Ominaisuudet
- Asetyyppi: Universal Rifles
- Materiaali: Aluminum
- Viimeistely: Silver
- Toimituksen paino: 0,249kg
- Toimituksen korkeus: 58mm
- Toimituksen leveys: 61mm
- Toimituksen pituus: 160mm
Tuotenro: 352150100
Valm.nro: 575S
Kolme suuntaista säätöä täydelliseen asennukseen, korkeampiin pisteisiin ja parempaan ampumamukavuuteen. Peruslevy kiinnitetään aseeseen, tyyny kiinnitetään tyynylevyyn ja kierteinen putki tarjoaa yhteensä 1-1/8" sisään/ulos säätöä. Voit tehdä täydellisiä käännöksiä tai pysäyttää pyörimisen mihin tahansa kohtaan 360° ja lukita se kuusiokolopulttien avulla. Viistetty yläpinta mahdollistaa 1½" pystysuoran säädön. Liitä Breako Recoil Reducer putkeen siistiä ja kompaktia asennusta varten. Yhdistä Gracon säädettävän comb hardware kanssa luodaksesi oman "Try Stock".
Ilmainen toimitus alkaen 249,00 €.
Toimitusaika noin 2-4 viikkoa.
STANDARD ADJUSTABLE BUTT PLATE on täydellinen valinta ampumiseen, sillä se tarjoaa kolme eri säätömahdollisuutta, jotka takaavat täydellisen aseen istuvuuden, korkeammat pisteet ja parantuneen ampumamukavuuden.
Materiaalina on matta viimeistelty alumiini. Mittojen mukaan: 5-13/16" (14.7cm) pitkä x 2" (5cm) leveä x 9/16" (14.3mm) paksu (täydellisesti "sisään" säädetty). Peruslevyn kiinnitysreiät ovat 3¼" (82.5mm) keskeltä keskelle. Standardimalli pumppuille, over/under -aseille ja sivu-sivulle -aseille sisältää kierteellisen putken, joka on keskitetty kiinnitysreikien väliin. Vaatii 1-1/8" (28.6mm) reiän poraamisen tukkiin.
Boyd's SS Evolution 10/22 stock 17.8.2016
I wanted to make the Boyd's ss Evolution stock fit me better. I use it for sage rats and after a day of shooting my neck would start hurting. This adjusts down about 3/4" and twists out out which was perfect to raise the comb of the stock and fit my shoulder. A few mods were needed like drilling holes. I have not shaped it to the stock yet. However, once I do I will duracoat it to match the receiver. I would buy another once I fit this one.
Just right 20.7.2015
I mounted this plate on an old single-barrel Winchester 101 Trap that I recently purchased. Stock had been cut so far back to the point it was midway in the slope of the Monte Carlo. It had also been cut at such a "custom" angle that spacers and a thick pad would not have allowed for a proper fit. The gun was absolutely useless for me although I knew that going in.
I installed one of these along with a T550 Pachmayr Trap Pad. Fitting the plates was tedious with much "cut, grind, and try" but the end result is a great fitting stock. I polished the exposed edges to a shiny finish with a sequence of filing, sanding, and rubbing with 0000 steel wool and "Mother's Aluminum Mag Polish." Due to the Monte Carlo being butchered, I had to lower the pad to what appears to be an excessive amount, but with the adjustments on this plate, I was able to get a perfect fit for me. The option of fitting the plate to the size of the recoil pad rather than fitting the recoil pad to a stock or a spacer has allowed for a greater area for recoil to occur. Might help with felt recoil.
You don't have to be a machinist or an expert gunsmith to install this plate, but basic wood and metal working skills are essential. The fitting of the plates to the stock and recoil pad and the use of a forstner bit near an existing hole takes time and patience.
Kohdattiin virhe tämän sisällön lataamisessa. Päivitä sivu jatkaaksesi. Jos ongelma jatkuu, ota yhteyttä asiakaspalveluumme.