We are pleased to be able to provide these beautiful, original pattern, British-made Hydraulic Dent Raisers. For the gunsmith, these Dent Raisers have proven to be one of the most sought after tools in our line. Few jobs are a greater challenge - or cause more customer concern - than removing a dent from a prize shotgun.To be able to remove such a damaging blemish with the ease, precision and perfection that this tool provides is gratifying beyond words. A tool you want to own ... A tool to cherish and care for. Not only will it make your customers happy, but it will also prove to be profitable for you at the same time!Actually, the dent raiser is a hydraulic jack of tremendous force with pressure controlled by the Allen screw in the handle. Because of the pressures involved, the best of steels and heat-treating procedures have been used in its production to ensure ease of maintenance and years of trouble-free use.EASE OF OPERATIONSimple and easy to operate. Hold the tool along the outside of the barrel, lining up the small anvil in the head even with the center of the dent. Slide the collar flush against the barrelbreech or muzzle (whichever end is closer to the dent) and lock the collar tightly into place.Now, insert the Dent Raiser into the barrel, bringing the collar flat against the end of the barrel and centering the anvil in the head directly under the dent. Gently turn the Allen screw in and watch the dent come up. When the dent is completely up (you must be careful not to bulge the barrel because the tool is so powerful), relieve the hydraulic pressure against the anvil by loosening the Allen screw. Re-apply pressure until resistance is just felt and you can turn the tool handle back and forth without too much pressure. Turn in the Allen screw and twist and burnish. Repeat until the dent is completely removed.No outside hammering or peening is required, so no hammer marks to polish out and no need to reblue the barrel. Just a fast, Professional job that will bring joy to your customer and fame and fortune to you! (NOTE: The Hydraulic Dent Raiser will not remove nicks/gouges in the steel that may have been caused along with the dent. Careful drawfiling and polishing can take care of most of these, and rebluing will be required - which your customer should understand.)Detailed operating and maintenance instructions.
Arvioiden lukumäärä: 2
Arvostelut brownells.com sivustolla: 2
Arvioiden keskiarvo: 4,5
Rais'n Dents(3.6.2011)
This dent raiser is worth its weight in gold. Yes it is a bit expensive....but it does what it says and does it with percussion. In order to do quality work you need quality tools and this tool is percussion quality.
Right Tool, Wrong Job(8.5.2013)
I order this thinking I could use it to raise the factory dimples in my 1187 shotgun magazine tube, along with being able to remove barrel dents. The tool will not expand to the necessary diameter to accomplish raising the factory magazine dents. I'm certain that it will work well for it's designed purpose of removing barrel dings/dents.
Tuotenro: 080083012 BROWNELLS 12 GAUGE DENT RAISER Meillä on ilo voi tarjota nämä kauniit, alkuperäiset kuvio, brittiläinen-kokoonpantu hydraulinen Dent Raisers. Aseseppä, nämä Dent Raisers on osoittautunut yksi halutuimmista kun keinot linjamme. Vähän työpaikkoja ovat suurempi haaste - tai huolestuttavat enemmän asiakas - kuin lommo poistaminen palkinnon haulikko. Voi poistaa haitallisia kauneusvirhe helppous, tarkkuus ja täydellisyyteen, että tämä työkalu tarjoaa on ilahduttavaa puheet. Haluat oman työkalu... Työkalu vaalia ja huolehtia. Se tekee asiakkaiden onnellisia, mutta se myös osoittautuu kannattavaa sinulle samaan aikaan! Oikeastaan dent kasvattaja on hydraulisylinterillä valtava voima paine valvottu luona kahva kuusiokoloruuveihin. Mukana paineiden vuoksi paras teräkset ja Lämpökäsittelynunet menettelyjä on käytetty tuotantoaan huollon helppous ja vuoden ongelmattoman käytön varmistamiseksi. HELPOSTI OPERATIONSimple ja helppo käyttää. Pikkusormella pitkin ulkopuolella tynnyri tasata pieni anvil päähän edes lommo center. Diojen kaulus huuhtele barrelbreech tai kuonon (kumpi lopulta on lähempänä lommo) ja lukita kaulus tiukasti paikalleen. Kiinnitä Dent kasvattaja tynnyriin tuo tasainen vastaan tynnyri loppuun kaulus ja keskitys anvil pään suoraan alle lommo. Varovasti kääntää Allen ruuvi ja katsella dent keksiä. Kun lommo on täysin ajan (sinun on oltava varovainen, ettei pullistuma tynnyri, koska työkalu on niin voimakas), lievittää Hydraulipaine vastaan alasimen löysäämällä Allen ruuvi. Uudelleen painostusta, kunnes vain vastustuksen ja ota työkalu kahva edestakaisin ilman liikaa paineita. Käännä kuusiokoloruuveihin ja kierre ja kiillottaa. Toista kunnes lommo poistetaan kokonaan. Ei ulkopuolella takomalla eli vasarointi on tarvittaessa, joten eikä vasara merkkejä Puolan ja ei tarvitse reblue piipun. Vain nopeasti, ammattimainen työpaikka, joka tuo iloa asiakkaan ja mainetta ja kunniaa sinulle! (Huomautus: Hydraulinen Dent kasvattaja ei poista naarmuja/gouges, teräs, joka aiheutti sekä lommo. Huolellinen drawfiling ja kiillotus voi hoitaa useimmat näistä, ja rebluing tarvitaan - asiakkaan pitäisi ymmärtää.) Yksityiskohtaiset käyttö- ja huolto-ohjeet.
449.9EUR0449,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Tuotenro: 080083016 BROWNELLS 16 GAUGE DENT RAISER Meillä on ilo voi tarjota nämä kauniit, alkuperäiset kuvio, brittiläinen-kokoonpantu hydraulinen Dent Raisers. Aseseppä, nämä Dent Raisers on osoittautunut yksi halutuimmista kun keinot linjamme. Vähän työpaikkoja ovat suurempi haaste - tai huolestuttavat enemmän asiakas - kuin lommo poistaminen palkinnon haulikko. Voi poistaa haitallisia kauneusvirhe helppous, tarkkuus ja täydellisyyteen, että tämä työkalu tarjoaa on ilahduttavaa puheet. Haluat oman työkalu... Työkalu vaalia ja huolehtia. Se tekee asiakkaiden onnellisia, mutta se myös osoittautuu kannattavaa sinulle samaan aikaan! Oikeastaan dent kasvattaja on hydraulisylinterillä valtava voima paine valvottu luona kahva kuusiokoloruuveihin. Mukana paineiden vuoksi paras teräkset ja Lämpökäsittelynunet menettelyjä on käytetty tuotantoaan huollon helppous ja vuoden ongelmattoman käytön varmistamiseksi. HELPOSTI OPERATIONSimple ja helppo käyttää. Pikkusormella pitkin ulkopuolella tynnyri tasata pieni anvil päähän edes lommo center. Diojen kaulus huuhtele barrelbreech tai kuonon (kumpi lopulta on lähempänä lommo) ja lukita kaulus tiukasti paikalleen. Kiinnitä Dent kasvattaja tynnyriin tuo tasainen vastaan tynnyri loppuun kaulus ja keskitys anvil pään suoraan alle lommo. Varovasti kääntää Allen ruuvi ja katsella dent keksiä. Kun lommo on täysin ajan (sinun on oltava varovainen, ettei pullistuma tynnyri, koska työkalu on niin voimakas), lievittää Hydraulipaine vastaan alasimen löysäämällä Allen ruuvi. Uudelleen painostusta, kunnes vain vastustuksen ja ota työkalu kahva edestakaisin ilman liikaa paineita. Käännä kuusiokoloruuveihin ja kierre ja kiillottaa. Toista kunnes lommo poistetaan kokonaan. Ei ulkopuolella takomalla eli vasarointi on tarvittaessa, joten eikä vasara merkkejä Puolan ja ei tarvitse reblue piipun. Vain nopeasti, ammattimainen työpaikka, joka tuo iloa asiakkaan ja mainetta ja kunniaa sinulle! (Huomautus: Hydraulinen Dent kasvattaja ei poista naarmuja/gouges, teräs, joka aiheutti sekä lommo. Huolellinen drawfiling ja kiillotus voi hoitaa useimmat näistä, ja rebluing tarvitaan - asiakkaan pitäisi ymmärtää.) Yksityiskohtaiset käyttö- ja huolto-ohjeet.
469.9EUR0469,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Tuotenro: 080083020 BROWNELLS 20 GAUGE DENT RAISER Meillä on ilo voi tarjota nämä kauniit, alkuperäiset kuvio, brittiläinen-kokoonpantu hydraulinen Dent Raisers. Aseseppä, nämä Dent Raisers on osoittautunut yksi halutuimmista kun keinot linjamme. Vähän työpaikkoja ovat suurempi haaste - tai huolestuttavat enemmän asiakas - kuin lommo poistaminen palkinnon haulikko. Voi poistaa haitallisia kauneusvirhe helppous, tarkkuus ja täydellisyyteen, että tämä työkalu tarjoaa on ilahduttavaa puheet. Haluat oman työkalu... Työkalu vaalia ja huolehtia. Se tekee asiakkaiden onnellisia, mutta se myös osoittautuu kannattavaa sinulle samaan aikaan! Oikeastaan dent kasvattaja on hydraulisylinterillä valtava voima paine valvottu luona kahva kuusiokoloruuveihin. Mukana paineiden vuoksi paras teräkset ja Lämpökäsittelynunet menettelyjä on käytetty tuotantoaan huollon helppous ja vuoden ongelmattoman käytön varmistamiseksi. HELPOSTI OPERATIONSimple ja helppo käyttää. Pikkusormella pitkin ulkopuolella tynnyri tasata pieni anvil päähän edes lommo center. Diojen kaulus huuhtele barrelbreech tai kuonon (kumpi lopulta on lähempänä lommo) ja lukita kaulus tiukasti paikalleen. Kiinnitä Dent kasvattaja tynnyriin tuo tasainen vastaan tynnyri loppuun kaulus ja keskitys anvil pään suoraan alle lommo. Varovasti kääntää Allen ruuvi ja katsella dent keksiä. Kun lommo on täysin ajan (sinun on oltava varovainen, ettei pullistuma tynnyri, koska työkalu on niin voimakas), lievittää Hydraulipaine vastaan alasimen löysäämällä Allen ruuvi. Uudelleen painostusta, kunnes vain vastustuksen ja ota työkalu kahva edestakaisin ilman liikaa paineita. Käännä kuusiokoloruuveihin ja kierre ja kiillottaa. Toista kunnes lommo poistetaan kokonaan. Ei ulkopuolella takomalla eli vasarointi on tarvittaessa, joten eikä vasara merkkejä Puolan ja ei tarvitse reblue piipun. Vain nopeasti, ammattimainen työpaikka, joka tuo iloa asiakkaan ja mainetta ja kunniaa sinulle! (Huomautus: Hydraulinen Dent kasvattaja ei poista naarmuja/gouges, teräs, joka aiheutti sekä lommo. Huolellinen drawfiling ja kiillotus voi hoitaa useimmat näistä, ja rebluing tarvitaan - asiakkaan pitäisi ymmärtää.) Yksityiskohtaiset käyttö- ja huolto-ohjeet.
479.9EUR0479,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
We are pleased to be able to provide these beautiful, original pattern, British-made Hydraulic Dent Raisers. For the gunsmith, these Dent Raisers have proven to be one of the most sought after tools in our line. Few jobs are a greater challenge - or cause more customer concern - than removing a dent from a prize shotgun.To be able to remove such a damaging blemish with the ease, precision and perfection that this tool provides is gratifying beyond words. A tool you want to own ... A tool to cherish and care for. Not only will it make your customers happy, but it will also prove to be profitable for you at the same time!Actually, the dent raiser is a hydraulic jack of tremendous force with pressure controlled by the Allen screw in the handle. Because of the pressures involved, the best of steels and heat-treating procedures have been used in its production to ensure ease of maintenance and years of trouble-free use.EASE OF OPERATIONSimple and easy to operate. Hold the tool along the outside of the barrel, lining up the small anvil in the head even with the center of the dent. Slide the collar flush against the barrelbreech or muzzle (whichever end is closer to the dent) and lock the collar tightly into place.Now, insert the Dent Raiser into the barrel, bringing the collar flat against the end of the barrel and centering the anvil in the head directly under the dent. Gently turn the Allen screw in and watch the dent come up. When the dent is completely up (you must be careful not to bulge the barrel because the tool is so powerful), relieve the hydraulic pressure against the anvil by loosening the Allen screw. Re-apply pressure until resistance is just felt and you can turn the tool handle back and forth without too much pressure. Turn in the Allen screw and twist and burnish. Repeat until the dent is completely removed.No outside hammering or peening is required, so no hammer marks to polish out and no need to reblue the barrel. Just a fast, Professional job that will bring joy to your customer and fame and fortune to you! (NOTE: The Hydraulic Dent Raiser will not remove nicks/gouges in the steel that may have been caused along with the dent. Careful drawfiling and polishing can take care of most of these, and rebluing will be required - which your customer should understand.)Detailed operating and maintenance instructions.
Arvioiden lukumäärä: 2
Arvostelut brownells.com sivustolla: 2
Arvioiden keskiarvo: 4,5
Rais'n Dents(3.6.2011)
This dent raiser is worth its weight in gold. Yes it is a bit expensive....but it does what it says and does it with percussion. In order to do quality work you need quality tools and this tool is percussion quality.
Right Tool, Wrong Job(8.5.2013)
I order this thinking I could use it to raise the factory dimples in my 1187 shotgun magazine tube, along with being able to remove barrel dents. The tool will not expand to the necessary diameter to accomplish raising the factory magazine dents. I'm certain that it will work well for it's designed purpose of removing barrel dings/dents.