38,000 PSI;Flows At 650\ F. Highest Silver-Bearing Content Available In A Non-Zinc Solder
Higher tensile strength for a stronger bond on joints that are subject to a high degree of stress or vibration. Contains 95% Cadmium and 5% Silver that flows free at 640° to 650° F. (maximum temp. 740° F.). Bonds quickly to all types of steel including stainless steel. Not affected by hot, caustic bluing solutions or by baking after spray-finish applications. Use with Copper Bond Flux and adequate ventilation.
SPECS: Wire - 1/16" (1.6mm) diameter.
Lisää...
Asiakasarviot: BROWNELLS HIGH TEMP HI-FORCE 44 SOLDER 1/4LB WIRE
Arvioiden lukumäärä: 2
Arvostelut brownells.com sivustolla: 2
Arvioiden keskiarvo: 1
Can anyone get this to work?(18.5.2011)
I've used Force 44 for many years. And I also use higher temp silver solders. But for the life of me, I can't get this stuff to adhere to anything, especially stainlesses. And the Copper Bond Flux is being used. Originally it was purchased to reattach a shotgun rib. This is a tedious process (for me) anyway. I thought the complications of that job were the problem. But since, I've tried a dozen times to attach sight ramps and such with it, and always remove all and start over with a solder that works for me. If anyone gets it to work, I'm missing something not in the instructions.
Not for stainless(23.7.2012)
I tried to use this to install a front sight onto a stainless steel Ruger Blackhawk. I've been soldering, brazing, and welding since I was a teenager (a very long time ago). If your working on stainless, this is NOT for you.
Tuotenro: 080649501 BROWNELLS HIGH TEMP HI-FORCE 44 SOLDER 1OZ WIRE Valmistajan tuotenumero: NONE Korkeampi vetolujuus siteiden nivelet ovat suurta stressiä tai tärinää. Sisältää 95 % kadmiumia ja 5 % hopeaa virrata vapaasti 640 ° 650° F. (maksimi lämpötila 740° F.). Joukkovelkakirjojen nopeasti kaikenlaisesta myös ruostumattomasta teräksestä. Ei vaikuta kuuma, Kaustinen bluing ratkaisuja tai Paistamisen jälkeen spray-maali sovelluksia. Käytä kupari Bond Flux ja riittävä ilmanvaihto.
22.9EUR022,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Paino:
1.0 oz
Toimituksen paino: 0,023kgKorkeus: 8mmLeveys: 104mmPituus: 175mm
Tuotekuvaus
Made in USA
Tuotenro: 080649590 BROWNELLS HIGH TEMP HI-FORCE 44 SOLDER 1LB WIRE Korkeampi vetolujuus siteiden nivelet ovat suurta stressiä tai tärinää. Sisältää 95 % kadmiumia ja 5 % hopeaa virrata vapaasti 640 ° 650° F. (maksimi lämpötila 740° F.). Joukkovelkakirjojen nopeasti kaikenlaisesta myös ruostumattomasta teräksestä. Ei vaikuta kuuma, Kaustinen bluing ratkaisuja tai Paistamisen jälkeen spray-maali sovelluksia. Käytä kupari Bond Flux ja riittävä ilmanvaihto.
154.9EUR0154,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
38,000 PSI;Flows At 650\ F. Highest Silver-Bearing Content Available In A Non-Zinc Solder
Higher tensile strength for a stronger bond on joints that are subject to a high degree of stress or vibration. Contains 95% Cadmium and 5% Silver that flows free at 640° to 650° F. (maximum temp. 740° F.). Bonds quickly to all types of steel including stainless steel. Not affected by hot, caustic bluing solutions or by baking after spray-finish applications. Use with Copper Bond Flux and adequate ventilation.
SPECS: Wire - 1/16" (1.6mm) diameter.
Lisää...
Asiakasarviot: BROWNELLS HIGH TEMP HI-FORCE 44 SOLDER 1/4LB WIRE
Arvioiden lukumäärä: 2
Arvostelut brownells.com sivustolla: 2
Arvioiden keskiarvo: 1
Can anyone get this to work?(18.5.2011)
I've used Force 44 for many years. And I also use higher temp silver solders. But for the life of me, I can't get this stuff to adhere to anything, especially stainlesses. And the Copper Bond Flux is being used. Originally it was purchased to reattach a shotgun rib. This is a tedious process (for me) anyway. I thought the complications of that job were the problem. But since, I've tried a dozen times to attach sight ramps and such with it, and always remove all and start over with a solder that works for me. If anyone gets it to work, I'm missing something not in the instructions.
Not for stainless(23.7.2012)
I tried to use this to install a front sight onto a stainless steel Ruger Blackhawk. I've been soldering, brazing, and welding since I was a teenager (a very long time ago). If your working on stainless, this is NOT for you.