Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
SIG SAUER P220 10MM HUNTER VORTEX VIPER/VENOM SIGHT MOUNT

841370115983 296000674
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
84.9 84.9 1 EUR
Tuotenro: 296000674
EGW SIG SAUER P220 10MM HUNTER VORTEX VIPER/VENOM SIGHT MOUNT
Valmistajan tuotenumero: 49328 841370115983 EGW:n punapistetähtäimet on tarkoitettu asennettavaksi vasemmalta oikealle (kun piippu osoittaa eteenpäin). Jyväkiskossa on progressiivinen kartio helpottamaan asennusta. Poista vain aseen takatähtäin ja korvaa se EGW:n kiinnikkeellä, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter punapistetähtäimen. Voit milloin tahansa ottaa kiinnikkeen pois ja palauttaa takatähtäimen. Asennustarvikkeet sisältyvät. Asennusohjeet: Poista takatähtäin* Asenna EGW:n tähtäinkiinnike jyväkiskoon Kiristä kiinnitysruuvi (jos sovellettavissa) Aseta punapistetähtäin EGW:n tähtäinkiinnikkeelle (punapistetähtäimen ja kiinnikkeen väliin asetettu pieni paperinpala helpottaa irrottamista ja pitää Loctiten pois punapistetähtäimestä.) Levitä sinistä Loctitea mukana tuleviin kiinnitysruuveihin Kiristä kiinnitysruuvit momenttiin 15in/lbs 2 Kupukantaruuvia - Mukana Vortex Viper ja Venom -tähtäimille 2 Litteäkantaruuvia - Mukana Burris FastFire ja Docter -tähtäimille Mukana tulevien ruuvien asennukseen tarvitaan 5/64 tuuman kuusiokoloavain. Aseen muokkaaminen voi mitätöidä valmistajan takuun. Tämän tuotteen tulisi asentaa ja tarkistaa pätevä aseseppä. Vastuuta ei oteta vahingoista tai vammoista, jotka saattavat aiheutua tämän tuotteen väärästä asennuksesta tai käytöstä.
84.9 EUR 0 84,90 € *
Ilmoita saatavuudesta
Loppu varastosta. Saatavuus ei tiedossa.
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: P220 Super Match SAO, P220 10mm Hunter Materiaali: Aluminum Merkki: Sig Sauer Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: P220 Super Match SAO,P220 10mm Hunter Materiaali: Aluminum Tyyli: Tactical Valmistaja: Sig Sauer Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Uutiskirje