Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
COLT GOLD CUP VORTEX RAZOR SIGHT MOUNT

841370113040 296000694
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Colt Gold Cup Colt Trooper Mark 3 Colt Python Colt Anaconda* This is for Colt models with the Elliason style adjustable rear sight. The elevation screw from the original rear sight is re-used in the center hole on this mount unless you have an Anaconda. An extra screw is available for purchase below as well. *Anacondas require a new elevation screw due to the design of the elevation screw supplied with the gun.
84.9 84.9 1 EUR
Tuotenro: 296000694
EGW COLT GOLD CUP VORTEX RAZOR SIGHT MOUNT
Valmistajan tuotenumero: 49441 841370113040 Poista vain aseen takatähtäin ja korvaa se EGW:n kiinnikkeellä, jotta voit asentaa Vortex Razorin, C-More RTS:n tai STS:n punapistetähtäimen. Voit milloin tahansa ottaa kiinnikkeen pois ja laittaa takatähtäimen takaisin paikalleen. Kiinnitystarvikkeet sisältyvät pakettiin. Asennusohjeet: Poista takatähtäin* Asenna EGW:n tähtäinkisko jyvään Kiristä asetuspultti (jos sovellettavissa) Aseta punapistetähtäin EGW:n tähtäinkiskoon (punapistetähtäimen ja tähtäinkiskon väliin asetettu pieni paperinpala helpottaa irrottamista ja pitää Loctiten poissa punapistetähtäimestä.) Levitä sinistä Loctitea mukana tuleviin kiinnitysruuveihin Kiristä kiinnitysruuvit momenttiin 15in/lbs Mukana toimitettuihin ruuveihin tarvitaan 5/64 tuuman kuusiokoloavain asennusta varten. Tämä kiinnike sopii seuraaviin Colt-malleihin: Colt Gold Cup Colt Trooper Mark 3 Colt Python Colt Anaconda* Tämä on Colt-malleille, joissa on Elliason-tyylinen säädettävä takatähtäin. Alkuperäisen takatähtäimen korkeussäätöruuvi käytetään uudelleen tämän kiinnikkeen keskireiässä, ellei sinulla ole Anacondaa. Anacondat vaativat uuden korkeussäätöruuvin aseen mukana toimitetun korkeussäätöruuvin suunnittelun vuoksi.
84.9 EUR 0 84,90 € *
Ilmoita saatavuudesta
Ei saatavilla.
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: Gold Cup, Anaconda, Python, Trooper Materiaali: Aluminum Merkki: Colt Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: Trooper,Gold Cup,Anaconda,Python Materiaali: Aluminum Tyyli: Tactical Valmistaja: Colt Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Colt Gold Cup Colt Trooper Mark 3 Colt Python Colt Anaconda* This is for Colt models with the Elliason style adjustable rear sight. The elevation screw from the original rear sight is re-used in the center hole on this mount unless you have an Anaconda. An extra screw is available for purchase below as well. *Anacondas require a new elevation screw due to the design of the elevation screw supplied with the gun.
Uutiskirje