Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
FN FNS, FNX VORTEX VIPER/VENOM SIGHT MOUNT

841370114528 296000656
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount will not work with FN FNP or FN 5.7.
84.9 84.9 1 EUR
Tuotenro: 296000656
EGW SIGHT MOUNT FOR VORTEX VIPER/VENOM FITS FN/FNS/FNX BLACK
Valmistajan tuotenumero: 49304 841370114528 EGW punapistetähtäimet on tarkoitettu asennettavaksi vasemmalta oikealle (kun aseen suuaukko on eteenpäin suunnattu). Urassa on progressiivinen kaltevuus helpottamaan asennusta. Poista vain aseesi takatähtäin ja korvaa se EGW-kiinnikkeellä, jotta voit asentaa Vortex Viper/Venom-, Burris FastFire- tai Docter-punapistetähtäimen. Voit milloin tahansa ottaa kiinnikkeen pois ja palauttaa takatähtäimesi. Asennustarvikkeet sisältyvät pakkaukseen. Asennusohjeet: Poista takatähtäin* Asenna EGW-tähtäinkiinnike uraan Kiristä asetuspultti (jos sovellettavissa) Aseta punapistetähtäin EGW-tähtäinkiinnikkeelle (punapistetähtäimen ja kiinnikkeen väliin asetettu pieni paperinpala helpottaa poistamista ja pitää Loctite-liiman poissa punapistetähtäimestä.) Levitä sinistä Loctite-liimaa mukana tuleviin kiinnitysruuveihin Kiristä kiinnitysruuvit 15 tuumapoundin momenttiin 2 kantaan upotettua ruuvia - Mukana Vortex Viper- ja Venom-tähtäimiin 2 litteää pääruuvia - Mukana Burris FastFire- ja Docter-tähtäimiin Tämän kiinnikkeen mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Aseen muuntaminen voi mitätöidä valmistajan takuun. Tämän tuotteen tulisi asentaa ja tarkistaa pätevä aseseppä. Vastuuta ei oteta vahingoista tai loukkaantumisista, jotka voivat aiheutua tämän tuotteen virheellisestä asennuksesta tai käytöstä. Tämä kiinnike ei sovi FN FNP- tai FN 5.7 -aseisiin.
84.9 EUR 1 84,90 € *
Toimitusaika noin 2-4 viikkoa.
1 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: FNX, FNS Materiaali: Aluminum Merkki: FN Tyyppi: Tactical Väri: Black

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: FNS,FNX Materiaali: Aluminum Tyyli: Tactical Valmistaja: FN Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount will not work with FN FNP or FN 5.7.
Uutiskirje