Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

EGW
CZ P10C, P10F VORTEX VIPER/VENOM SIGHT MOUNT

841370116010 296000675
"""""""""""EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount Does Not Fit: CZ P10C Optics Ready CZ P10F Optics Ready
84.9 84.9 1 EUR
Tuotenro: 296000675
EGW SIGHT MOUNT FOR VORTEX VIPER/VENOM FITS CZ P10C/P10F BLACK
Valmistajan tuotenumero: 49329 841370116010 EGW-pistetähtäimet on tarkoitettu asennettaviksi vasemmalta oikealle (kun piippu osoittaa eteenpäin). Liukuprofiilissa on progressiivinen kartio helpottamaan asennusta. Poista vain aseen takatähtäin ja korvaa se EGW-kiinnikkeellä, jotta voit asentaa Vortex Viper/Venom-, Burris FastFire- tai Docter-pistetähtäimen. Voit milloin tahansa poistaa kiinnikkeen ja laittaa takatähtäimen takaisin paikalleen. Asennustarvikkeet sisältyvät pakkaukseen. Asennusohjeet: Poista takatähtäin* Asenna EGW-tähtäinkisko liukuprofiiliin Kiristä asetuspultti (jos sovellettavissa) Aseta pistetähtäin EGW-tähtäinkiskoon (pistetähtäimen ja kiskon väliin laitettu pieni paperinpala helpottaa irrottamista ja pitää Loctiten poissa pistetähtäimestä.) Levitä sinistä Loctitea mukana toimitettuihin kiinnitysruuveihin Kiristä kiinnitysruuvit momenttiin 15 in/lb 2 kantaan upotettua ruuvia - Mukana Vortex Viper- ja Venom-tähtäimiä varten 2 litteää päätä olevaa ruuvia - Mukana Burris FastFire- ja Docter-tähtäimiä varten Mukana olevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen asennukseen. Aseen muokkaaminen voi mitätöidä valmistajan takuun. Tämän tuotteen tulisi asentaa ja tarkistaa pätevä aseaseppä. Vastuuta ei oteta vahingoista tai vammoista, jotka voivat johtua tämän tuotteen virheellisestä asennuksesta tai käytöstä. Tämä kiinnike ei sovi: CZ P10C Optics Ready CZ P10F Optics Ready
84.9 EUR 3 84,90 € *
Toimitusaika noin 2-4 viikkoa.
3 kpl. USA:n varastossa
Ominaisuudet: Jalustojen lukumäärä: 1-Piece Malli: P-10F, P-10C Materiaali: Aluminum Merkki: CZ Tyyppi: Tactical Väri: Black

Top takeaways

  1. EGW-pistetähtäimet on helppo asentaa poistamalla takatähtäin ja korvaamalla se EGW-kiinnikkeellä, johon voi asentaa Vortex Viper/Venom-, Burris FastFire- tai Docter-pistetähtäimen.
  2. Asennustarvikkeet ja ohjeet sisältyvät pakkaukseen, ja mukana tulevat ruuvit vaativat 5/64 tuuman kuusiokoloavaimen.
  3. Kiinnike ei sovi CZ P10C Optics Ready ja CZ P10F Optics Ready -malleihin, ja asennus tulisi suorittaa pätevän aseasepän toimesta.

Ominaisuudet

Jalustojen lukumäärä: 1-Piece Malli: P-10F,P-10C Materiaali: Aluminum Tyyli: Tactical Valmistaja: CZ Väri: Black Toimituksen paino: 0,045kg Toimituksen korkeus: 25mm Toimituksen leveys: 76mm Toimituksen pituus: 140mm

Tuotekuvaus

Made in USA




EGW-pistetähtäin kiinnike Vortex Viper/Venom sopii CZ P10C/P10F. Helppo asennus ja irrotus. Sisältää asennustarvikkeet. 🚀🔧 Hanki omasi nyt! 🛒

"""""""""""EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount Does Not Fit: CZ P10C Optics Ready CZ P10F Optics Ready
Varastossa
194,90 € * 194,90 € - 204,90 €*
0
Uutiskirje