These Drop Tube Adapters are the adapters needed to allow your Redding powder measures to accept the Sinclair Custom Drop Tubes. Machined from stainless steel, these adapters replace your existing drop tubes and allow you to use Custom Drop Tubes of various lengths. Work with either the Redding Measure stand or the Sinclair Powder Measure Stand.
Lisää...
Nämä Drop Tube Adapterit ovat tarvittavia sovittimia, joiden avulla Redding-jauhemittarit voivat käyttää Sinclair Custom Drop Tubeja. Ruostumattomasta teräksestä koneistetut sovittimet korvaavat olemassa olevat tiputusputket ja mahdollistavat eri pituisten Custom Drop Tubejen käytön. Toimivat sekä Redding Measure -telineen että Sinclair Powder Measure Standin kanssa.
Lisää...
Asiakasarviot: SINCLAIR INTERNATIONAL REDDING DROP TUBE ADAPTER
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 2
Takes some work to use(7.9.2012)
I bought this adapter to use with my Redding 3BR measure. It's the one on the right in the image. It comes with no instructions, but it was fairly obvious that the short green drop tube on the 3BR had to go. I tried twisting it off while holding it in a small hobby vise. No joy. So I tried a bigger vise with serrated jaws and it came off without too much marring. Next, the adaptor would only screw on for about a half turn. The threadform in the adapter is different than on the 3BR. So, I stuck the adpater in the same vise with a towel around it and used the 3BR as a thread. Using some oil and many back and forth turns, the adapter threads were deepened enough to screw on by hand. When steel goes against aluminum, steel wins. Now that it is installed, I am happy with it, although it is a bit marred. Nonetheless, it should have fit right off.
Tuotenro: 749010851 SINCLAIR INTERNATIONAL REDDING DROP TUBE ADAPTER Nämä Drop Tube Adapterit ovat tarvittavia sovittimia, joiden avulla Redding-jauhemittarit voivat käyttää Sinclair Custom Drop Tubeja. Ruostumattomasta teräksestä koneistetut sovittimet korvaavat olemassa olevat tiputusputket ja mahdollistavat eri pituisten Custom Drop Tubejen käytön. Toimivat sekä Redding Measure -telineen että Sinclair Powder Measure Standin kanssa.
These Drop Tube Adapters are the adapters needed to allow your Redding powder measures to accept the Sinclair Custom Drop Tubes. Machined from stainless steel, these adapters replace your existing drop tubes and allow you to use Custom Drop Tubes of various lengths. Work with either the Redding Measure stand or the Sinclair Powder Measure Stand.
Lisää...
Nämä Drop Tube Adapterit ovat tarvittavia sovittimia, joiden avulla Redding-jauhemittarit voivat käyttää Sinclair Custom Drop Tubeja. Ruostumattomasta teräksestä koneistetut sovittimet korvaavat olemassa olevat tiputusputket ja mahdollistavat eri pituisten Custom Drop Tubejen käytön. Toimivat sekä Redding Measure -telineen että Sinclair Powder Measure Standin kanssa.
Lisää...
Asiakasarviot: SINCLAIR INTERNATIONAL REDDING DROP TUBE ADAPTER
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 2
Takes some work to use(7.9.2012)
I bought this adapter to use with my Redding 3BR measure. It's the one on the right in the image. It comes with no instructions, but it was fairly obvious that the short green drop tube on the 3BR had to go. I tried twisting it off while holding it in a small hobby vise. No joy. So I tried a bigger vise with serrated jaws and it came off without too much marring. Next, the adaptor would only screw on for about a half turn. The threadform in the adapter is different than on the 3BR. So, I stuck the adpater in the same vise with a towel around it and used the 3BR as a thread. Using some oil and many back and forth turns, the adapter threads were deepened enough to screw on by hand. When steel goes against aluminum, steel wins. Now that it is installed, I am happy with it, although it is a bit marred. Nonetheless, it should have fit right off.