This is the third hand you’ve been looking for when peening or swaging 1911 Auto frame rails. All-steel tool holds a single or double Slide Fitting Bar securely in place, without movement. Makes striking our Rail Swaging Punches with a hammer easier and more accurate. Designed by William A. Smith III of Marietta, Georgia. Must be used with current production Slide Fitting Bars equipped with through holes.
SPECS: Steel, blued. 2.6" (6.6cm) wide. Includes two, 1⁄4"-28 Allen screws and washers.
Lisää...
Tämä on se kolmas käsi, jota olet etsinyt peennatessasi tai laajentaessasi 1911 Auto -runkokiskoja. Täysin teräksestä valmistettu työkalu pitää yhden tai kahden Slide Fitting Barin tukevasti paikoillaan ilman liikkumista. Tekee Rail Swaging Punches -työkalulla vasaralla lyömisestä helpompaa ja tarkempaa. Suunnitellut William A. Smith III Mariettasta, Georgiasta. On käytettävä nykytuotannon Slide Fitting Bareja, jotka on varustettu läpivienteillä.
TEKNISET TIEDOT: Terästä, sinistetty. Leveys 2.6" (6.6cm). Sisältää kaksi 1⁄4"-28 kuusiokoloruuvia ja aluslevyt.
Lisää...
Asiakasarviot: BROWNELLS 1911 SLIDE FITTING BAR HOLDING FIXTURE
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 4
Slide Bar Holding Fixture(6.9.2012)
This is a well designed tool and works well for its intended purpose. One thing I did not like about it is the tendency to rust. It's surface is not very well protected and if you don't treat it look out! After mine started to rust, I sanded the areas and put some of the bluing solution(much like you would treat a pistol) and so far it has worked well(no Rust)but that keeps it from getting five stars. Otherwise, should last a lifetime.
Tuotenro: 080745002 BROWNELLS 1911 SLIDE FITTING BAR HOLDING FIXTURE Valmistajan tuotenumero: BARHOLDER050806104778 Tämä on se kolmas käsi, jota olet etsinyt peennatessasi tai laajentaessasi 1911 Auto -runkokiskoja. Täysin teräksestä valmistettu työkalu pitää yhden tai kahden Slide Fitting Barin tukevasti paikoillaan ilman liikkumista. Tekee Rail Swaging Punches -työkalulla vasaralla lyömisestä helpompaa ja tarkempaa. Suunnitellut William A. Smith III Mariettasta, Georgiasta. On käytettävä nykytuotannon Slide Fitting Bareja, jotka on varustettu läpivienteillä.
This is the third hand you’ve been looking for when peening or swaging 1911 Auto frame rails. All-steel tool holds a single or double Slide Fitting Bar securely in place, without movement. Makes striking our Rail Swaging Punches with a hammer easier and more accurate. Designed by William A. Smith III of Marietta, Georgia. Must be used with current production Slide Fitting Bars equipped with through holes.
SPECS: Steel, blued. 2.6" (6.6cm) wide. Includes two, 1⁄4"-28 Allen screws and washers.
Lisää...
Tämä on se kolmas käsi, jota olet etsinyt peennatessasi tai laajentaessasi 1911 Auto -runkokiskoja. Täysin teräksestä valmistettu työkalu pitää yhden tai kahden Slide Fitting Barin tukevasti paikoillaan ilman liikkumista. Tekee Rail Swaging Punches -työkalulla vasaralla lyömisestä helpompaa ja tarkempaa. Suunnitellut William A. Smith III Mariettasta, Georgiasta. On käytettävä nykytuotannon Slide Fitting Bareja, jotka on varustettu läpivienteillä.
TEKNISET TIEDOT: Terästä, sinistetty. Leveys 2.6" (6.6cm). Sisältää kaksi 1⁄4"-28 kuusiokoloruuvia ja aluslevyt.
Lisää...
Asiakasarviot: BROWNELLS 1911 SLIDE FITTING BAR HOLDING FIXTURE
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 4
Slide Bar Holding Fixture(6.9.2012)
This is a well designed tool and works well for its intended purpose. One thing I did not like about it is the tendency to rust. It's surface is not very well protected and if you don't treat it look out! After mine started to rust, I sanded the areas and put some of the bluing solution(much like you would treat a pistol) and so far it has worked well(no Rust)but that keeps it from getting five stars. Otherwise, should last a lifetime.