Our special 65° shoulder Sight Base Cutter designed to cut dovetails for both standard Colt factory and mil-spec 1911 Autos, and for replacement sights like Wichita Hi-Mount, older Bo- Mar and others with a 65° shoulder. Some makers use a 60° dovetail on their rear sights and we also have a cutter to match them. For low-mount adjustable sights use the Standard Sight Base Cutter shown on this page. Actual cutting diameter is .330" so more than one pass will be required to install most sights. This is done on purpose to allow for factory variations in base width as well as milling tolerances. CAUTION: For use in milling machine only. High speed steel, 2" (5cm) long, 3⁄8" (9.5mm) diameter shank. 60° or 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.
Lisää...
34.943.92EUR
Tuotenro: 080621330 BROWNELLS 65 HSS SEMI-AUTO SIGHT BASE CUTTER .330" Meidän erityinen 65° olkapää näky Base leikkuri on tarkoitettu leikkaamaan vastaa standardin Colt tehdas ja mil-spec 1911 Autos ja korvaaminen nähtävyydet Wichita Hi-Mount, vanhemmat Bo-Mar ja muut 65° olkapää. Jotkut päättäjät käyttää 60° sovittaa taka nähtävyyksiä ja meillä on myös leikkuri vastaamaan niihin. Käytä matala-mount säädettävä nähtävyyksiä standardin näky Base leikkuri tällä sivulla. Varsinainen leikkaus halkaisija on. 330" niin enemmän kuin kerralla tulee asentaa useimmat nähtävyydet. Tämä on tehty tarkoituksella mahdollistaa tehdas vaihtelut jalan leveys sekä jyrsintä toleranssit. Varoitus: käytetään jyrsinkone vain. Pikaterästä, 2"(5cm) pitkä, 3⁄8" (9,5 mm) halkaisija varsi. 60 tai 65° olkapää. EIVÄT ylitä 700 rpm, suurempi nopeus RIKKOA hampaat.
Tuotenro: 080621331 BROWNELLS 60 HSS SEMI-AUTO BASE CUTTER .330" Meidän erityinen 65° olkapää näky Base leikkuri on tarkoitettu leikkaamaan vastaa standardin Colt tehdas ja mil-spec 1911 Autos ja korvaaminen nähtävyydet Wichita Hi-Mount, vanhemmat Bo-Mar ja muut 65° olkapää. Jotkut päättäjät käyttää 60° sovittaa taka nähtävyyksiä ja meillä on myös leikkuri vastaamaan niihin. Käytä matala-mount säädettävä nähtävyyksiä standardin näky Base leikkuri tällä sivulla. Varsinainen leikkaus halkaisija on. 330" niin enemmän kuin kerralla tulee asentaa useimmat nähtävyydet. Tämä on tehty tarkoituksella mahdollistaa tehdas vaihtelut jalan leveys sekä jyrsintä toleranssit. Varoitus: käytetään jyrsinkone vain. Pikaterästä, 2"(5cm) pitkä, 3⁄8" (9,5 mm) halkaisija varsi. 60 tai 65° olkapää. EIVÄT ylitä 700 rpm, suurempi nopeus RIKKOA hampaat.
Our special 65° shoulder Sight Base Cutter designed to cut dovetails for both standard Colt factory and mil-spec 1911 Autos, and for replacement sights like Wichita Hi-Mount, older Bo- Mar and others with a 65° shoulder. Some makers use a 60° dovetail on their rear sights and we also have a cutter to match them. For low-mount adjustable sights use the Standard Sight Base Cutter shown on this page. Actual cutting diameter is .330" so more than one pass will be required to install most sights. This is done on purpose to allow for factory variations in base width as well as milling tolerances. CAUTION: For use in milling machine only. High speed steel, 2" (5cm) long, 3⁄8" (9.5mm) diameter shank. 60° or 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.