It's easy to eliminate excess cylinder and yoke endplay with these stainless steel bearings. Made by pistolsmith Ron Power as an alternative to stretching the yoke. Whether rebuilding worn guns or building custom ones, these will help turn out a 1st-class job. Each pak contains 10 bearings of 1 thickness.
SPECS: Hardened 302 stainless steel. Cylinder Bearings - see chart. Yoke Bearings - .002" (.051mm) thick for S&W K,L,N.
Lisää...
Asiakasarviot: POWER CUSTOM YOKE ENDSHAKE BEARINGS, SMITH & WESSON K, L, N ONLY
Arvioiden lukumäärä: 2
Arvostelut brownells.com sivustolla: 2
Arvioiden keskiarvo: 5
Alternate use(11.5.2015)
I have used these on revolvers, but what I use them for more often is with action screws on bolt action rifles. instead of drilling down the screw recesses in a trigger guard or trimming the underside of the screw head, just put the proper number of these under the screw to align the screw slot with the long axis of the rifle. Much easier.
End Shake Shim(7.1.2017)
A few years back, I sent a revolver to S&W for excessive end shake. After big dollars to ship each way, the repair at S&W was $6.00. I later learned of these Power Custom Bearings....(end shake shims) Long story short, these shims work perfectly you just need to pay attention to the thread direction of the ejector rod/cylinder assembly. Some are left and some right depending on which dash your S&W is. Other that that, easy to install and saves huge dollars!
Tuotenro: 713012002 POWER CUSTOM YOKE ENDSHAKE BEARINGS, SMITH & WESSON K, L, N ONLY Valmistajan tuotenumero: PY2 Ies Endshake laakerit, Smith & Wesson K, L, N vain
34.9EUR634,90 €
*
Toimitusaika noin 2-4 viikkoa. 6 kpl. USA:n varastossa
Ominaisuudet:Malli: K Frame, L Frame, N FrameMerkki: Smith & Wesson
Tuotenro: 713100002 POWER CUSTOM PC-2 .002 (.051MM) THICK SMITH & WESSON K, L, N Valmistajan tuotenumero: PC2 Se on helppo poistaa ylimääräinen sylinteri ja ies endplay nämä ruostumattoman teräksen laakerit. Tehnyt pistolsmith Ron Power vaihtoehtona venyttely ikeen. Onko uudelleenrakentaminen kuluneet aseet tai rakennuksen mukautettuja niistä, ne auttavat osoittautua ensiluokkainen työ. Kunkin pak sisältää 10 laakerit 1 paksuus.
34.9EUR1534,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Ominaisuudet:Malli: K Frame, L Frame, N FrameMerkki: Smith & Wesson
Tuotenro: 713100004 POWER CUSTOM PC-4 .004 (.10MM) THICK SMITH & WESSON K, L, N Valmistajan tuotenumero: PC4 Se on helppo poistaa ylimääräinen sylinteri ja ies endplay nämä ruostumattoman teräksen laakerit. Tehnyt pistolsmith Ron Power vaihtoehtona venyttely ikeen. Onko uudelleenrakentaminen kuluneet aseet tai rakennuksen mukautettuja niistä, ne auttavat osoittautua ensiluokkainen työ. Kunkin pak sisältää 10 laakerit 1 paksuus.
34.9EUR434,90 €
*
Toimitusaika noin 2-4 viikkoa. 4 kpl. USA:n varastossa
Ominaisuudet:Malli: K Frame, L Frame, N FrameMerkki: Smith & Wesson
It's easy to eliminate excess cylinder and yoke endplay with these stainless steel bearings. Made by pistolsmith Ron Power as an alternative to stretching the yoke. Whether rebuilding worn guns or building custom ones, these will help turn out a 1st-class job. Each pak contains 10 bearings of 1 thickness.
SPECS: Hardened 302 stainless steel. Cylinder Bearings - see chart. Yoke Bearings - .002" (.051mm) thick for S&W K,L,N.
Lisää...
Asiakasarviot: POWER CUSTOM YOKE ENDSHAKE BEARINGS, SMITH & WESSON K, L, N ONLY
Arvioiden lukumäärä: 2
Arvostelut brownells.com sivustolla: 2
Arvioiden keskiarvo: 5
Alternate use(11.5.2015)
I have used these on revolvers, but what I use them for more often is with action screws on bolt action rifles. instead of drilling down the screw recesses in a trigger guard or trimming the underside of the screw head, just put the proper number of these under the screw to align the screw slot with the long axis of the rifle. Much easier.
End Shake Shim(7.1.2017)
A few years back, I sent a revolver to S&W for excessive end shake. After big dollars to ship each way, the repair at S&W was $6.00. I later learned of these Power Custom Bearings....(end shake shims) Long story short, these shims work perfectly you just need to pay attention to the thread direction of the ejector rod/cylinder assembly. Some are left and some right depending on which dash your S&W is. Other that that, easy to install and saves huge dollars!