Brownells Finland - Laajin valikoima aseen osia, lippaita, ammuntatarvikkeita, asesepän työkaluja ja optiikkaa Suomi

BROWNELLS
BOLT ACTION FIRING PIN REMOVAL TOOL

080000409
Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

154.9 154.9 1 EUR
Tuotenro: 080000409
BROWNELLS FIRING PIN REMOVAL TOOL Kolmas käsi Remington- ja Ruger® -kiväärin lukon iskutappien irrottamiseen ilman kadonneita osia tai kipeitä sormia, jotka joskus liittyvät tähän hankalaan tehtävään. Aseta oikea holkki työkalun päässä olevaan reikään. Ruuvaa iskutappi kokoonpano holkin sisään ja kiristä teräksinen varsi puristaaksesi ja lukitaksesi pääjousen. Ontto varsi suojaa iskutapin kärkeä, kun se liukuu tapin yli puristaen jousen. Ristitappi voidaan sitten ajaa ulos taltalla, ja jousen jännitys voidaan helpottaa vähitellen varren löysäämällä. Mukana holkkeja Remington 700 perheen ja Ruger M77® Mark II -kivääreille. Sisäänrakennettu säilytyspaikka pitää käyttämättömän holkin aina työkalun rungossa, joten se on aina käytettävissä, kun sitä tarvitset. HUOM: Ei sovi Rugerin vasenkätisiin toimintoihin.
154.9 EUR 0 154,90 € *
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Ominaisuudet: Malli: Universal Rifles Merkki: Ruger, Remington

Ominaisuudet

Malli: Universal Rifles Valmistaja: Remington,Ruger Toimituksen paino: 0,431kg Toimituksen korkeus: 58mm Toimituksen leveys: 112mm Toimituksen pituus: 183mm

Tuotekuvaus

Made in USA




Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

Uutiskirje